DIN EN ISO 11296-3:2011-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES
Hardcopy , PDF
05-01-2019
German, English
01-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings
7 Ancillary components
8 Fitness for purpose of the installed lining system
at the 'I' stage
9 Installation practice
Annex A (normative) - Factory folded heat reverted
polyethylene (PE) pipe - Determination of
memory ability
Annex B (normative) - Folded polyethylene (PE) pipe -
Determination of resistance to circumferential
tensile stress at constant temperature
Bibliography
This standard is included in DIN Handbook 13-4.
| DevelopmentNote |
Supersedes DIN EN 13566-3. (07/2011) DRAFT 2017 issued in September 2017. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 11296-3:2018 | Identical |
| EN ISO 11296-3:2011 | Identical |
| ISO 11296-3:2009 | Identical |
| DIN HDBK 13-4 : 10ED 2015 | ABWASSERTECHNIK 4 - ABWASSERKANAELE, ABWASSERLEITUNGEN - PLANUNG, VERLEGUNG, BETRIEB, SANIERUNG |
| DIN EN ISO 9967:2016-07 | THERMOPLASTICS PIPES - DETERMINATION OF CREEP RATIO (ISO 9967:2016) |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| DIN EN ISO 6259-1:2015-08 | THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL TEST METHOD (ISO 6259-1:2015) |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) |
| ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| DIN EN ISO 11295:2016-08 (Draft) | CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| DIN EN ISO 11296-1:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL |
| ISO 18373-1:2007 | Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature |
| DIN EN ISO 9969:2016-06 | THERMOPLASTICS PIPES - DETERMINATION OF RING STIFFNESS (ISO 9969:2016) |
| ISO 4435:2003 | Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 21138-1:2007 | Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.