DIN EN 681-1:2016-07 (Draft)
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016
Hardcopy , PDF
03-28-2022
German, German - English
07-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Classification
4 Requirements
5 Test pieces and temperature
6 Quality
7 Factory product control tests
8 Storage
9 Designation
10 Marking and labelling
Annexes
A (normative) Determination of stress relaxation in
tension
B (normative) Determination of compression set in hot
water at 110 Degree C
C (normative) Determination of splice strength
D (informative) Guidance on storage of seals
ZA (informative) Clauses of this European
Standard addressing the provisions of the
EU Construction Products Directive
This standard is included in DIN Handbook 12/5, 13-2, 13-5, 15-6 and 62-1. Defines requirements for materials used in vulcanized rubber seals for cold potable water supply (up to 50 degree C), hot potable and non-potable water supply (to 110 degree C) and drainage, sewerage and rainwater systems (continuous flow to 45 degree C and intermittent flow up to 95 degree C). Applies to seals for all materials including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastic.
| DevelopmentNote |
Partly supersedes DIN 4060 issue 12-1988. (09/2000) DRAFT 2016 issued in July 2016. (07/2016)
|
| DocumentType |
Draft
|
| Pages |
71
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Withdrawn
|
| Standards | Relationship |
| SN EN 681-1 : 1999 AMD 3 2006 | Identical |
| NEN EN 681-1 : 1996 AMD 3 2005 | Identical |
| BS EN 681-1:1996 | Identical |
| NS EN 681-1 : 96 AMD 3 2005 | Identical |
| NF EN 681-1 : 1996 AMD 3 2005 | Identical |
| UNI EN 681-1 : 2006 | Identical |
| I.S. EN 681-1:1996 | Identical |
| NBN EN 681-1 : 1996 AMD 3 2005 | Identical |
| UNE-EN 681-1:1996 | Identical |
| DIN 8063-3:2002-06 | PIPE JOINTS AND COMPONENTS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC U) FOR PIPES UNDER PRESSURE - PART 3: UNIONS - DIMENSIONS |
| DIN V 4034-1:2004-08 | PREFABRICATED CONCRETE MANHOLES, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - PART 1: REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY |
| DIN V 1201:2004-08 | CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY |
| DIN 28602:2000-05 | DUCTILE IRON PIPES AND FITTINGS - BOLTED GLAND JOINTS - ASSEMBLY, SOCKETS, COUNTER RING, SEALING RING, BOLTS AND NUTS |
| DIN 16874:2000-06 | PIPES AND FITTINGS OF HIGH-DENSITY POLYETHYLENE (PE-HD) FOR CABLE DUCTING - DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS |
| DIN 28601:2000-06 | DUCTILE IRON PIPES AND FITTINGS - SCREWED SOCKET JOINTS - ASSEMBLY, SOCKETS, SCREW RINGS, SEALING RINGS AND SLIP RINGS |
| DIN 28603:2002-05 | DUCTILE IRON PIPES AND FITTINGS - PUSH-IN JOINTS - SURVEY, SOCKETS AND GASKETS |
| DIN 16831-7:2004-02 | Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 7: Dimensions of bushings, flanges and selaing elements for socket welding |
| DIN HDBK 190 : 3ED 2006 | ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS THERMOPLASTISCHEN KUNSTSTOFFEN |
| DIN HDBK 160 : 4ED 2006 | WASSERVERSORGUNG 4 - ROHRE, FORMSTUECKE UND ZUBEHOER FUER WASSERLEITUNGEN (B) |
| DIN 16962-12:1999-10 | PIPE JOINTS AND COMPONENTS OF POLYPROPYLENE (PP) FOR PIPES UNDER PRESSURE, PP-H 100, PP-B 80 AND PP-R 80 - PART 12: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING; DIMENSIONS |
| DIN 16963-11:1999-10 | PIPE JOINTS AND COMPONENTS OF POLYETHYLENE (PE) FOR PIPES UNDER PRESSURE, PE 80 AND PE 100 - PART 11: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING - DIMENSIONS |
| DIN 16917-1:2015-10 | PIPES AND FITTINGS MADE OF THERMOPLASTIC MATERIALS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - LARGE PIPES OVER DN 1200 FOR UNDERGROUND INSTALLATION - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| DIN 8063-3:1980-07 | PIPE JOINT ASSEMBLIES AND FITTINGS FOR UNPLASTICIZED POLYVINYL CHLORIDE (PVC-U) PRESSURE PIPES - PART 3: DIMENSIONS OF SCREWED PIPE JOINT ASSEMBLIES |
| DIN HDBK 50 : 9ED 2000 | ABWASSERTECHNIK 2 - ROHRE UND FORMSTUECKE FUER DIE GEBAEUDEENTWAESSERUNG |
| DIN HDBK 13-2 : 11ED 2017 | ABWASSERTECHNIK 2 - ROHRE UND FORMSTUECKE FUER DIE GEBAEUDEENTWAESSERUNG |
| DIN HDBK 259 : 4ED 2007 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
| DIN HDBK 62-2 : 8ED 2010 | |
| DIN HDBK 12/5 : 9ED 2013 | |
| DIN HDBK 62-1 : 8ED 2010 | WASSERVERSORGUNG 2 - GUSS-, STAHLBETON- UND STAHLROHRE FUER WASSERLEITUNGEN |
| DIN HDBK 13-5 : 5ED 2015 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
| DIN HDBK 62 CD : 7ED 2004 | WASSERVERSORGUNG 2 - GUSS-, KUNSTSTOFF-, STAHLBETON- UND STAHLROHRE FUER WASSERLEITUNGEN |
| DIN HDBK 15-6 : 1ED 2012 |
| ISO 3302:1990 | Rubber — Dimensional tolerances for use with products |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO 2285:2013 | Rubber, vulcanized or thermoplastic Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| ISO 9691:1992 | Rubber — Recommendations for the workmanship of pipe joint rings — Description and classification of imperfections |
| ISO 4661-1:1993 | Rubber, vulcanized or thermoplastic Preparation of samples and test pieces Part 1: Physical tests |
| ISO 3384:2005 | Rubber, vulcanized or thermoplastic Determination of stress relaxation in compression at ambient and at elevated temperatures |
| ISO 3387:2012 | Rubber Determination of crystallization effects by hardness measurements |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 471:1995 | Rubber Temperatures, humidities and times for conditioning and testing |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 816:1983 | Rubber, vulcanized — Determination of tear strength of small test pieces (Delft test pieces) |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| ISO 1629:2013 | Rubber and latices — Nomenclature |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.