DIN EN 15551:2011-01
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RAILWAY APPLICATIONS - RAILWAY ROLLING STOCK - BUFFERS
Hardcopy , PDF
03-07-2021
English
01-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and designation
5 Requirements
6 Housing
Annex A (normative) - Maximum space envelope
of buffer
Annex B (normative) - Mechanical characteristics
of buffers Test methods
Annex C (normative) - Requirements for elastic systems
Annex D (normative) - Testing of static characteristics
of buffers
Annex E (normative) - Dynamic testing
Annex F (normative) - Endurance testing under
service load for elastic system
Annex G (normative) - Endurance testing under
buffing load for life-cycle simulation
Annex H (informative) - Guidelines for buffer
head materials
Annex I (normative) - Calculation of the width
of buffer heads
Annex J (normative) - Crashworthy buffers
for tank wagons
Annex K (normative) - Maximum space envelope
of crashworthy buffers
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 2008/57/EC
Bibliography
Describes the requirements for buffers with 105 mm, 110 mm and 150 mm stroke for vehicles or units which use buffers and screw coupling.
| DocumentType |
Standard
|
| Pages |
74
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 15551:2017 | Identical |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| UIC 527-1 : 3ED 2005 | COACHES, VANS AND WAGONS - DIMENSIONS OF BUFFER HEADS - TRACK LAYOUT ON S-CURVES |
| ISO 6507-4:2005 | Metallic materials Vickers hardness test Part 4: Tables of hardness values |
| ISO 815-2:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| UIC 827-1 : 2ED 1990 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF ELASTOMER COMPONENTS FOR BUFFERS |
| UIC 528 : 8ED 2007 | BUFFER GEAR FOR COACHES |
| ISO 148-2:2016 | Metallic materials — Charpy pendulum impact test — Part 2: Verification of testing machines |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| ISO 6507-2:2005 | Metallic materials Vickers hardness test Part 2: Verification and calibration of testing machines |
| ISO 11469:2016 | Plastics — Generic identification and marking of plastics products |
| UIC B36 RP 32 : 1989 | CHARACTERISTICS OF THE BUFFING AND DRAW GEAR OF WAGONS TO ENSURE THE SAFE RUNNING OF LONG VEHICLES IN SMALL RADIUS CURVES |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 10168:2004 | Steel products - Inspection documents - List of information and description |
| EN ISO 11469:2016 | Plastics - Generic identification and marking of plastics products (ISO 11469:2016) |
| ISO 6507-3:2005 | Metallic materials Vickers hardness test Part 3: Calibration of reference blocks |
| UIC B36 RP 30 : 1990 | REDUCTION OF ACCELERATION DURING BUFFING IMPACTS |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 15227:2008+A1:2010 | Railway applications - Crashworthiness requirements for railway vehicle bodies |
| EN 1370:2011 | Founding - Examination of surface condition |
| UIC 573 : 7ED 2007 | TECHNICAL CONDITIONS FOR THE CONSTRUCTION OF TANK WAGONS |
| ISO 148-3:2016 | Metallic materials — Charpy pendulum impact test — Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| NFF 10 102 : 1998 | RAILWAY ROLLING STOCK - BUFFERS FOR FREIGHT ROLLING STOCK - ENVELOPES AND COMPONENT PARTS |
| UIC 827-2 : 3ED 1981 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF STEEL RINGS FOR BUFFER SPRINGS |
| UIC 571-2 : 6ED 2001 | STANDARD WAGONS - ORDINARY BOGIE WAGONS - CHARACTERISTICS |
| EN ISO 148-2:2016 | Metallic materials - Charpy pendulum impact test - Part 2: Verification of testing machines (ISO 148-2:2016) |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN ISO 148-3:2016 | Metallic materials - Charpy pendulum impact test - Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines (ISO 148-3:2016) |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| UIC 535-2 : 4ED 2005 | STANDARDISATION AND POSITIONING ON WAGONS OF STEPS, END PLATFORMS, GANGWAYS, HANDRAILS, TOW HOOKS, AUTOMATIC COUPLER (AC), AUTOMATIC DRAW-ON COUPLING AND BRAKE VALVE CONTROLS ON THE UIC MEMBER RUS AND OSJD MEMBER RUS |
| UIC B36 RP 24 : 1984 | GUIDELINES FOR THE EXECUTION OF IMPACT TESTS WITH WAGONS (WITH SIDE BUFFERS OR WITH AUTOMATIC COUPLER) |
| UIC B12 RP 17 : 1997 | PROGRAMME OF TESTS TO BE CARRIED OUT ON WAGONS WITH STEEL UNDER FRAME AND BODY STRUCTURE (SUITABLE FOR BEING FITTED WITH THE AUTOMATIC BUFFING AND DRAW COUPLER) AND ON THEIR CAST STEEL FRAME BOGIES |
| UIC 840-2 : 3ED 1981 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF STEEL CASTINGS FOR TRACTIVE AND TRAILING STOCK |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.