DIN EN 12420:1999-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
COPPER AND COPPER ALLOYS - FORGINGS
Hardcopy , PDF
03-07-2021
English
01-01-1999
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Declaration of conformity and inspection
documentation
10 Marking, labelling, packaging
Annex A (informative) - Recommended guidelines
for design
Annex B (informative) - Tensile properties
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 97/23/EC,
Pressure Equipment Directive (PED)
Bibliography
This standard is included in DIN HDBK 456/3 E. Defines the composition, the property requirements and tolerances on dimensions and form for copper and copper alloy die and hand forgings.
| DevelopmentNote |
Supersedes DIN 17673-1 E, DIN 17673-2 E, DIN 17673-3 E, DIN 17673-4 E, DIN 17678-1 E, DIN 17678-2 E, DIN 17678-3 E and DIN 17678-4 E (07/2002)
|
| DocumentType |
Standard
|
| Pages |
56
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| UNI EN 12420 : 2014 | Identical |
| EN 12420:2014 | Identical |
| NS EN 12420 : 2014 | Identical |
| UNE-EN 12420:2015 | Identical |
| NBN EN 12420 : 2014 | Identical |
| I.S. EN 12420:2014 | Identical |
| SN EN 12420:2014 | Identical |
| NEN EN 12420 : 2014 | Identical |
| NF EN 12420 : 2014 | Identical |
| BS EN 12420:2014 | Identical |
| EN 1655:1997 | Copper and copper alloys - Declarations of conformity |
| EN 14977:2006 | Copper and copper alloys - Detection of tensile stress - 5 % ammonia test |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| EN ISO 80000-1:2013 | Quantities and units - Part 1: General (ISO 80000-1:2009 + Cor 1:2011) |
| EN 1412:2016 | Copper and copper alloys - European numbering system |
| EN ISO 1101:2017 | Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017) |
| ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1811-2:1988 | Copper and copper alloys — Selection and preparation of samples for chemical analysis — Part 2: Sampling of wrought products and castings |
| EN 1976:2012 | Copper and copper alloys - Cast unwrought copper products |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 6509:1981 | Corrosion of metals and alloys Determination of dezincification resistance of brass |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.