DIN EN 1151-1:2006-11
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: NON-AUTOMATIC CIRCULATION PUMPS, REQUIREMENTS, TESTING, MARKING
Hardcopy , PDF
04-01-2013
English
01-12-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Performance and safety requirements
5.1 Hydraulic characteristic
5.2 Rated power
5.3 Starting characteristics
5.4 Resistance to internal pressure
5.5 Temperature resistance
5.6 Resistance to thermal cycling
5.7 Venting and deblocking
5.8 Material- and design requirement
5.9 Fluid and structure borne noise emission
6 Test methods
6.1 General
6.2 Testing of the hydraulic characteristic
6.2.1 General
6.2.2 Test conditions
6.2.3 Testing of hydraulic performance
6.3 Measurement of rated power input
6.4 Starting conditions
6.5 Testing of resistance to internal pressure
6.6 Testing of temperature resistance
6.7 Testing of resistance to thermal cycling
6.7.1 Motor supply voltage
6.7.2 Intermittent operation
6.8 Venting and deblocking
6.9 Toxicity, biological and microbiological test
7 Information for use
7.1 General
7.2 Instruction handbook
7.3 Marking
Annex A (informative) Additives
Bibliography
National Annex NA (informative) Bibliography
Defines general principles for the construction, use and testing of circulation pumps of the glandless type, having a rated power input P[1] less than or equal to 200 W, intended to be used in heating installations and domestic hot water service installations.
| DevelopmentNote |
Supersedes DIN EN 1151 E. (07/2007)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| NEN EN 1151-1 : 2006 C1 2007 | Identical |
| NF EN 1151-1 : 2006 | Identical |
| SN EN 1151-1 : 2006 | Identical |
| PREN 1151-1 : DRAFT 2009 | Identical |
| NBN EN 1151-1 : 2006 COR 2007 | Identical |
| UNI EN 1151-1 : 2006 | Identical |
| UNE-EN 1151-1:2007 | Identical |
| NS EN 1151-1 : 2006 AC 2007 | Identical |
| I.S. EN 1151-1:2006 | Identical |
| BS EN 1151-1:2006 | Identical |
| DIN 49445:1991-10 | THREE-POLE SOCKET-OUTLETS WITH N- AND EARTHING CONTACTS 16 A 400/230 V A.C.; PRINCIPAL DIMENSIONS |
| VDI 2035:1979-07 | Prevention of damage by means of corrosion and scale formation in warm-water-heating-systems |
| EN 60034-1:2010/corrigendum Oct. 2010 | ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE |
| DIN 4751-2:1994-10 | MEDIUM TEMPERATURE HOT WATER SYSTEMS (MTHWS) WITH A BOILER FLOW TEMPERATURE UP TO 120 DEG C - SPECIFICATION FOR SEALED SYSTEMS USING THERMOSTATIC CONTROL - SAFETY EQUIPMENT |
| DIN 49448:1991-10 | THREE-POLE PLUG WITH N- AND EARTHING CONTACTS 25 A 400/230 V AC; PRINCIPAL DIMENSIONS |
| HD 472 S1:1989/AC:2013 | NOMINAL VOLTAGES FOR LOW-VOLTAGE PUBLIC ELECTRICITY SUPPLY SYSTEMS |
| IEC 60335-2-51:2002+AMD1:2008+AMD2:2011 CSV | Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations |
| EN 60335-2-51:2003/A2:2012 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-51: PARTICULAR REQUIREMENTS FOR STATIONARY CIRCULATION PUMPS FOR HEATING AND SERVICE WATER INSTALLATIONS (IEC 60335-2-51:2002/A2:2011) |
| EN 809 : 1998 COR 2010 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| DIN 4751-3:1993-02 | MEDIUM TEMPERATURE HOT WATER SYSTEMS (MTHWS) WITH A BOILER FLOW TEMPERATURE UP TO 95 DEGREE C AND FORCED FLOW BOILERS WITH RATED OUTPUT UP TO 50 KW - SPECIFICATION FOR SEALED SYSTEMS USING THERMOSTATIC CONTROL - SAFETY EQUIPMENT |
| BS 5449:1990 | Specification for forced circulation hot water central heating systems for domestic premises |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| DIN 49447:1991-10 | THREE-POLE SOCKET-OUTLETS WITH N- AND EARTHING CONTACTS 25 A 400/230 V AC; PRINCIPAL DIMENSIONS |
| DIN 4751-1:1994-10 | MEDIUM TEMPERATURE HOT WATER SYSTEMS (MTHWS) WITH A BOILER FLOW TEMPERATURE UP TO 120 DEGREE C - SPECIFICATION FOR OPEN SYSTEMS AND SEALED SYSTEMS WITH PRESSURISATION BY GRAVITY USING A COLUMN OF WATER OR BY SAFETY VALVES - SAFETY EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.