DIN EN 10242:1995-03
Current
The latest, up-to-date edition.
THREADED PIPE FITTING IN MALLEABLE CAST IRON
Hardcopy , PDF
01-01-1995
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Fittingstypen
4 Begriffe und Definitionen
5 Werkstoffe
6 Konstruktion
7 Masse und Toleranzen
8 Gewinde
9 Herstellung
10 Eigenschaften
11 Prüfung und Kontrolle
12 Qualitätssicherungssystem
13 Bezeichnung der Fittings
14 Kennzeichnung
Tabellen der masslich genormten Fittingstypen und
Grössen (Tabellen 8 bis 26)
Anhang A (normativ) Tempergussfittings für
Gewindeverbindungen nach ISO 7-1, jedoch mit
Innengewinde Rc
Anhang B (informativ) Qualitätssicherungssystem und
Bewertung der Konformität
Anhang C (informativ) Zusammenhang mit den
wesentlichen Anforderungen der
Bauproduktenrichtlinie (89/106 EG)
Anhang D (informativ) Zusammenhang zwischen
Fittinggrösse und Nennweite (DN)
Anhang E (informativ) Literaturhinweise
This standard is included in DIN HDBK 15-6. Specifies the requirements for the design and performance of threaded pipe fittings in malleable cast iron.
| DevelopmentNote |
Supersedes DIN 2950 (07/2002)
|
| DocumentType |
Standard
|
| Pages |
46
|
| ProductNote |
NEW CHILD AMD 2 IS NOW ADDED
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNE-EN 10242:1995 | Identical |
| I.S. EN 10242:1995 | Identical |
| NS EN 10242 : 94 AMD 2 2003 | Identical |
| NEN EN 10242 : 1995 AMD 2 2003 | Identical |
| NBN EN 10242 : 95 AMD 2 2003 | Identical |
| BS EN 10242:1995 | Identical |
| UNI EN 10242 : 2009 | Identical |
| NF EN 10242 : 95 AMD 2 2004 | Identical |
| SN EN 10242 : 1995 AMD 2 2003 | Identical |
| DIN HDBK 15-6 : 1ED 2012 | |
| DIN 1988-600:2010-12 | Codes of practice for drinking water installations - Part 600: Drinking water installations in connection with fire fighting and fire protection installations; DVGW code of practice |
| BWB TL 4240-0072 : 1ED 2008 | RESCUE AND RECOVERY EQUIPMENT, LIGHT |
| DIN 1988-200:2012-05 | Codes of practice for drinking water installations - Part 200: Installation Type A (closed system) - Planning, components, apparatus, materials; DVGW code of practice |
| DIN 50930-6:2013-10 | Corrosion of metals - Corrosion of metallic materials under corrosion load by water inside of pipes, tanks and apparatus - Part 6: Evaluation process and requirements regarding the hygienic suitability in contact with drinking water |
| DIN 30690-1:2016-04 | CONSTRUCTION ELEMENTS IN THE GAS SUPPLY SYSTEM - PART 1: REQUIREMENTS FOR CONSTRUCTION ELEMENTS IN GAS SUPPLY SYSTEMS |
| DIN 14462:2012-09 | Water conduit for fire extinguishing - Planning, installation, operation and maintenance of fire hose systems and pillar fire hydrant and underground fire systems |
| DIN 1988-7:2004-12 | CODES OF PRACTICE FOR DRINKING WATER INSTALLATIONS (TRWI) - PART 7: PREVENTION OF CORROSION DAMAGE AND CALCAREOUS DEPOSIT FORMATION - DVGW CODE OF PRACTICE |
| EN 29002 : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN PRODUCTION & INSTALLATION |
| DIN ISO 228-2:1988-07 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - VERIFICATION BY MEANS OF LIMIT GAUGES |
| ISO 2859:1974 | Sampling procedures and tables for inspection by attributes |
| DIN ISO 2859-1:2014-08 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011) |
| EN 1562:2012 | Founding - Malleable cast irons |
| DIN ISO 228-1:1994-12 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| PREN 1562 : DRAFT 2009 | FOUNDING - MALLEABLE CAST IRONS |
| EN ISO 9002:1994/AC:1997 | QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION |
| ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| DIN 50049:1992-04 | METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| DIN 2999-1:1983-07 | PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS |
| DIN 50988-1:1984-02 | MEASUREMENT OF COATING THICKNESS; DETERMINATION OF THE MASS PER UNIT AREA OF ZINC- AND TIN-COATINGS ON FERROUS MATERIALS BY DISSOLUTION OF THE COATING MATERIAL; GRAVIMETRIC METHOD |
| ISO 9002:1994 | Quality systems — Model for quality assurance in production, installation and servicing |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| DIN EN 26708 : 1993 | |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
| DIN EN ISO 9001:2015-11 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015) |
| ISO 1460:1992 | Metallic coatings Hot dip galvanized coatings on ferrous materials Gravimetric determination of the mass per unit area |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| EN 29001 : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN DESIGN/DEVELOPMENT, PRODUCTION, INSTALLATION & SERVICING |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.