DIN EN 10217-3:2005-04
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES
Hardcopy , PDF
08-01-2019
English
01-01-2005
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Symbole
5 Einteilung und Bezeichnung
5.1 Einteilung
5.2 Bezeichnung
6 Bestellangaben
6.1 Verbindliche Angaben
6.2 Optionen
6.3 Bestellbeispiel
7 Herstellverfahren
7.1 Stahlherstellungsverfahren
7.2 Desoxidationsverfahren
7.3 Rohrherstellung und Lieferzustand
8 Anforderungen
8.1 Allgemeines
8.2 Chemische Zusammensetzung
8.3 Mechanische Eigenschaften
8.4 Oberflächenbeschaffenheit und innere Beschaffenheit
8.5 Geradheit
8.6 Endenvorbereitung
8.7 Masse, längenbezogene Masse und Grenzabmasse
9 Prüfung
9.1 Arten der Prüfung
9.2 Prüfbescheinigungen
9.3 Zusammenfassung der Prüfungen
10 Probenahme
10.1 Prüfumfang
10.2 Vorbereitung der Probenabschnitte und Proben
11 Prüfverfahren
11.1 Chemische Analyse
11.2 Zugversuch
11.3 Ringfaltversuch
11.4 Ringzugversuch
11.5 Aufweitversuch
11.6 Ringaufdornversuch
11.7 Schweissnaht-Biegeversuch
11.8 Kerbschlagbiegeversuch
11.9 Dichtheitsprüfung
11.10 Masskontrolle
11.11 Sichtprüfung
11.12 Zerstörungsfreie Prüfung
11.13 Materialidentifizierung
11.14 Wiederholungsprüfungen, Sortieren und Nachbehandlung
12 Kennzeichnung
12.1 Verbindliche Kennzeichnung
12.2 Zusätzliche Kennzeichnung
13 Oberflächenschutz
Anhang A (normativ) Qualifizierung des Schweissverfahrens
für die Herstellung von SAW-Rohren
Anhang B (normativ) Eigenschaften bei erhöhten
Temperaturen für die Stahlsorten P275NL1 und
P275NL2
Anhang ZA (informativ) Abschnitte in dieser Europäischen
Norm, die grundlegende Anforderungen oder andere
Vorgaben von EU-Richtlinien betreffen
Literaturhinweise
This standard is included in DIN Handbook 15, 15-2, 403/1 and 403. Describes the technical delivery condition in two test categories for welded tubes of circular cross section, made of weldable alloy fine grain steel.
| DevelopmentNote |
Supersedes DIN 17178 (08/2002) DRAFT 2014 issued in October 2014. (10/2014)
|
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| I.S. EN 10217-3:2002 | Identical |
| NEN EN 10217-3 : 2002 AMD 1 2005 | Identical |
| UNI EN 10217-3 : 2005 | Identical |
| BS EN 10217-3:2002 | Identical |
| EN 10217-3:2019 | Identical |
| SN EN 10217-3 : 2002 AMD 1 2005 | Identical |
| ONORM EN 10217-3 : 2007 | Identical |
| NBN EN 10217-3 : 2002 AMD 1 2005 | Identical |
| NS EN 10217-3 : 2002 AMD 1 2005 | Identical |
| UNE-EN 10217-3:2003 | Identical |
| NF EN 10217-3 : 2002 AMD 1 2005 | Identical |
| DIN HDBK 15-2 : 12ED 2014 | STAHLROHRLEITUNGEN - BAND 2: ROHRE - TECHNISCHE LIEFERBEDINGUNGEN |
| DIN HDBK 15 : 10ED 2005 | STEEL PIPELINES 1 - STANDARDS ON DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS |
| DIN HDBK 403 : 4ED 2005 | IRON AND STEEL: QUALITY STANDARDS 3 - PRESSURE VESSELS AND PIPELINES - FINE GRAIN STEEL - STEEL WITH LOW TEMPERATURE TOUGHNESS - STEEL WITH ELEVATED TEMPERATURE PROPERTIES - STEEL FOR PRESSURE APPLICATIONS - CASTINGS AND FORGINGS |
| DIN HDBK 403/1 : 6ED 2015 | IRON AND STEEL - QUALITY STANDARDS 3/1 - SEAMLESS AND WELDED STEEL TUBES FOR PRESSURE APPLICATIONS |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10246-17:2000 | Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections |
| EN 10246-1:1996 | Non destructive testing of steel tubes - Part 1: Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness |
| CR 10261 : 1995 | ECISS INFORMATION CIRCULAR 11 - IRON AND STEEL - REVIEW OF AVAILABLE METHODS OF CHEMICAL ANALYSIS |
| EN 10234 : 1993 | METALLIC MATERIALS - TUBE - DRIFT EXPANDING TEST |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10237 : 1993 | METALLIC MATERIALS - TUBE - RING TENSILE TEST |
| EN 10002-5:1991 | Metallic materials - Tensile testing - Part 5: Method of testing at elevated temperature |
| EN 1321:1996 | Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds |
| EN 10246-6:1999 | Non-destructive testing of steel tubes - Part 6: Automatic full peripheral ultrasonic testing of seamless steel tubes for the detection of transverse imperfections |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| EN 10256:2000 | Non-destructive testing of steel tubes - Qualification and competence of level 1 and 2 non-destructive testing personnel |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| EN 895:1995 | Destructive tests on welds in metallic materials - Transverse tensile test |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EURONORM 103 : 1971 | MICROSCOPIC DETERMINATION OF THE FERRITE OR AUSTENITIC GRAIN SIZE OF STEELS |
| EN 910 : 1996 | DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN 10236 : 1993 | METALLIC MATERIALS - TUBE - RING EXPANDING TEST |
| EN 10246-7:2005 | Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections |
| EN 10246-16:2000 | Non-destructive testing of steel tubes - Part 16: Automatic ultrasonic testing of the area adjacent to the weld seam of welded steel tubes for the detection of laminar imperfections |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN 10246-10:2000 | Non-destructive testing of steel tubes - Part 10: Radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10233 : 1993 | METALLIC MATERIALS - TUBE - FLATTENING TEST |
| EN 760:1996 | Welding consumables - Fluxes for submerged arc welding - Classification |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10246-9:2000 | Non-destructive testing of steel tubes - Part 9: Automatic ultrasonic testing of the weld seam of submerged arc welded steel tubes for the detection of longitudinal and/or transverse imperfections |
| EN 10246-3:1999 | Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ENV 10220 : 1993 | SEAMLESS AND WELDED STEEL TUBES - DIMENSIONS AND MASSES PER UNIT LENGTH |
| EN 10020:2000 | Definition and classification of grades of steel |
| EN 10246-15:2000 | Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections |
| EN 10246-14:1999 | Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| EN 10246-8:1999 | Non-destructive testing of steel tubes - Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections |
| CR 10260 : 1998 | DESIGNATION SYSTEMS FOR STEEL - ADDITIONAL SYMBOLS |
| EN 10246-5 : 1999 | NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 5: AUTOMATIC FULL PERIPHERAL MAGNETIC TRANSDUCER/FLUX LEAKAGE TESTING OF SEAMLESS AND WELDED (EXCEPT SUBMERGED ARC WELDED) FERROMAGNETIC STEEL TUBES FOR THE DETECTION OF LONGITUDINAL IMPERFECTIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.