DIN 336:2003-07
Current
The latest, up-to-date edition.
DIAMETERS OF DRILLS FOR MINOR DIAMETERS OF TAPPED THREADS
Hardcopy , PDF
German, English
01-01-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.Kein Inhaltsverzeichnis in der Norm vorhanden.
This standard is included in DIN Handbook 6. Gives sizes of drills for use prior to tapping parallel screw threads of nominal length of engagement, the drill diameter being approximately equal to the nominal diameter of the thread minus the pitch. Does not apply to threads produced by cold forming.
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Supersedes |
| DIN HDBK 6-1 : 13ED 2009 | |
| VDI 3334:2015-03 | Machining of internal threads |
| DIN HDBK 6 : 14ED 2016 | BOHRER, SENKER, REIBAHLEN, GEWINDEBOHRER, GEWINDESCHNEIDEISEN UND GEWINDEFURCHER |
| DIN HDBK 6-2 : 13ED 2009 | GEWINDEBOHRER, GEWINDESCHNEIDEISEN UND GEWINDEFURCHER - NORMEN, WERKZEUGE |
| DIN 6539:1991-05 | CONTINUOUS PARALLEL SHANK SOLID HARDMETAL TWIST DRILLS; DIMENSIONS |
| DIN 346:2006-11 | MORSE TAPER SHANK TWIST DRILLS, OVERSIZE SHANK |
| ISO 2306:1972 | Drills for use prior to tapping screw threads |
| DIN ISO 228-1:1994-12 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| DIN 2999-1:1983-07 | PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS |
| DIN 6538-1:1993-06 | TWIST DRILLS WITH HARDMETAL CUTTING EDGES WITH REINFORCED PARALLEL SHANK; DIMENSIONS |
| DIN 338:2006-11 | Parallel shank twist drills, jobber series |
| ISO 5864:1993 | ISO inch screw threads Allowances and tolerances |
| DIN 13-2:1999-11 | ISO general purpose metric screw threads - Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm |
| DIN 339:2006-11 | Parallel shank twist drills for use in jig bushes |
| DIN 345:2006-11 | MORSE TAPER SHANK TWIST DRILLS |
| DIN 1897:2006-11 | PARALLEL SHANK TWIST DRILLS, STUB SERIES |
| DIN 6537:1993-04 | SOLID-HARDMETAL TWIST DRILLS WITH STEPPED PARALLEL SHANK; DIMENSIONS |
| DIN 341:2006-11 | MORSE TAPER SHANK TWIST DRILLS FOR USE IN JIG BUSHES, LONG SERIES |
| ISO 235:2016 | Parallel shank jobber and stub series drills and Morse taper shank drills |
| DIN 340:2006-11 | Parallel shank twist drills, long series |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.