DIN 1913-1:1984-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
COVERED ELECTRODES FOR THE JOINT WELDING OF UNALLOYED AND LOW ALLOY STEEL - CLASSIFICATION, DESIGNATION, TECHNICAL DELIVERY CONDITIONS
01-01-1995
01-12-2013
1 Anwendungsbereich
2 Bezeichnung
2.1 Kennzahl bzw. Kennziffern für die
mechanischen Gütewerte
2.2 Typ-Kurzzeichen für die Umhüllung
2.3 Kennziffern für die Klasseneinteilung
2.4 Kennzahlen für das Ausbringen
2.5 Bezeichnungsbeispiele
3 Klassenbeschreibung
4 Hinweise für die Anwendung
5 Technische Lieferbedingungen
5.1 Beschaffenheit
5.2 Masse und Bestellbezeichnung
5.3 Mechanische Gütewerte
5.4 Chemische Zusammensetzung
5.5 Kennzeichnung
5.6 Verpackung
5.7 Abnahmeprüfungen
6 Lagerung und Rücktrocknung
(Proposal for an European Standard) 1984 VERSION TRANSLATED INTO ENGLISH, DRAFT NOT YET TRANSLATED Covers covered electrodes suitable for the joint welding of unalloyed and low alloy steels as shown in table 6 or comparable steels and grades of cast steel.
| DevelopmentNote |
Supersedes DIN 1913 and DIN 1913-2 (07/2002)
|
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| ISO 544:2011 | Similar to |
| EN 499 : 1994 | Similar to |
| DIN 65152:1984-03 | AEROSPACE; LIFT FIXTURES; CONDITIONS FOR COMPUTATION AND ACCEPTANCE |
| DIN 8975-2 E : 1978 | REFRIGERATION PLANTS; SAFETY REQUIREMENTS FOR CONSTRUCTION, ERECTION AND OPERATION; SELECTION OF MATERIALS FOR REFRIGERATION PLANTS |
| DIN EN 22553:1997-03 | WELDED, BRAZED AND SOLDERED JOINTS - SYMBOLIC REPRESENTATION ON DRAWINGS |
| DIN 8571:1981-07 | WELDING FILLER MATERIALS AND AUXILIARY MATERIALS FOR METAL-WELDING - DEFINITIONS, CLASSIFICATION |
| DIN 17182:1992-05 | GENERAL-PURPOSE STEEL CASTINGS WITH ENHANCED WELDABILITY AND HIGHER TOUGHNESS - TECHNICAL DELIVERY CONDITIONS |
| DIN 15155:1986-12 | PALLETS - BOX PALLET WITH MESH SIDE PANELS AND 2 FRONTSIDE FLAPS |
| DIN 8555-1:1983-11 | FILLER METALS USED IN SURFACING - SOLID WIRES, FILLER RODS, WIRE ELECTRODES, DESIGNATION, TECHNICAL DELIVERY CONDITIONS |
| ISO 547:1975 | Electrodes for the welding of mild steel and low alloy high tensile steel Lengths and tolerance |
| DIN 8556-1:1986-05 | FILLER METALS FOR WELDING STAINLESS AND HEAT RESISTANT STEELS; DESIGNATION, TECHNICAL DELIVERY CONDITIONS |
| DIN 8573-1:1983-01 | FILLER METALS FOR WELDING UNALLOYED AND LOW ALLOY CAST IRON MATERIALS; DESIGNATION; TECHNICAL DELIVERY CONDITIONS |
| DIN 17100:1980-01 | STEELS FOR GENERAL STRUCTURAL PURPOSES - QUALITY STANDARD |
| ISO 544:2011 | Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markings |
| ISO 2560:2009 | Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification |
| DIN 32525-2:1979-08 | TESTING FILLER METALS BY MEANS OF WELD METAL SPECIMENS - TEST PIECES FOR DETERMINING CHEMICAL COMPOSITION WITH LOW HEAT INPUT |
| DIN 17102:1983-10 | WELDABLE NORMALIZED FINE GRAIN STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS FOR PLATE, STRIP, WIDE FLATS, SECTIONS AND BARS |
| DIN 50049:1992-04 | METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS |
| DIN 8572-1:1981-03 | DETERMINATION OF HYDROGEN IN DEPOSITED WELD METAL; MANUAL ARC WELDING WITH COVERED ELECTRODE |
| DIN 1626:1984-10 | WELDED CIRCULAR UNALLOYED STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS |
| DIN 32525-1:1981-12 | TESTING FILLER METALS BY MEANS OF WELD METAL SPECIMENS - ARC WELDED TEST PIECES, SPECIMENS FOR MECHANICAL-TECHNOLOGICAL TESTS |
| EURONORM 20 : 1974 | DEFINITIONS AND CLASSIFICATION OF STEEL GRADES |
| DIN 1630:1984-10 | HIGH PERFORMANCE SEAMLESS CIRCULAR UNALLOYED STEEL TUBES - TECHNICAL DELIVERY CONDITIONS |
| DIN 1629:1984-10 | SEAMLESS CIRCULAR UNALLOYED STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS |
| DIN 17155:1983-10 | CREEP RESISTANT STEEL PLATE AND STRIP - TECHNICAL DELIVERY CONDITIONS |
| DIN 8555-1:1983-11 | FILLER METALS USED IN SURFACING - SOLID WIRES, FILLER RODS, WIRE ELECTRODES, DESIGNATION, TECHNICAL DELIVERY CONDITIONS |
| DIN 1628:1984-10 | HIGH PERFORMANCE WELDED CIRCULAR UNALLOYED STEEL TUBES - TECHNICAL DELIVERY CONDITIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.