DEFSTAN 61-12(PT12)SEC3/2(2008) : 2008
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
WIRES, CORDS AND CABLES - ELECTRICAL-METRIC UNITS - PART 12 SECTION 3: CABLES, TELEPHONE (FOR FIELD USE)
Hardcopy , PDF
11-14-2019
English
01-01-2008
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Warning
3 Normative References
4 SPECIFICATION FOR CABLE, TELEPHONE, CARRIER QUAD, TYPE P
MARK 4
4.1 INTRODUCTION
4.2 MATERIALS
4.3 CONSTRUCTION AND DIMENSIONS
4.4 TENSIONING
4.5 TESTS ON MATERIALS
4.6 PHYSICAL TESTS ON COMPLETED CABLE AFTER TENSIONING
4.7 ELECTRICAL TESTS
4.8 TEST PROCEDURES
4.9 PACKAGING AND LABELLING
5 SPECIFICATION FOR CABLE, TELEPHONE, LIGHTWEIGHT QUD
5.1 INTRODUCTION
5.2 MATERIALS
5.3 CONSTRUCTION AND DIMENSIONS
5.4 TESTS ON MATERIALS
5.5 PHYSICAL TESTS ON COMPLETED CABLE
5.6 ELECTRICAL TESTS
5.7 TEST PROCEDURES
5.8 PACKAGING AND LABELLING
6 SPECIFICATION FOR CABLE, TELEPHONE, 10 - PAIR
6.1 INTRODUCTION
6.2 MATERIALS
6.3 CONSTRUCTION AND DIMENSIONS
6.4 TESTS ON MATERIALS
6.5 PHYSICAL TESTS ON COMPLETED CABLE
6.6 ELECTRICAL TESTS
6.7 TEST PROCEDURES
6.8 PACKAGING AND LABELLING
7 SPECIFICATION FOR CABLE, TELEPHONE, D 10, MARK 4, TWISTED
7.1 INTRODUCTION
7.2 MATERIALS
7.3 CONSTRUCTION AND DIMENSIONS
7.4 TESTS ON MATERIALS
7.5 PHYSICAL TESTS ON COMPLETED CABLE
7.6 ELECTRICAL TESTS
7.7 TEST PROCEDURES
7.8 PACKAGING AND LABELLING
8 TEST AND MEASUREMENT METHODS
8.1 COMPRESSIVE STRENGTH TEST ON POLYETHYLENE INSULATION
8.2 HEAT TEST ON POLYETHYLENE INSULATION OR NYLON SHEATH
8.3 COLD BEND TEST ON POLYETHYLENE INSULATION OR NYLON SHEATH
8.4 HEAT TEST ON PVC SHEATH
8.5 COLD BEND TEST ON COMPLETED CABLE (AT -40 DEGREES C OR
-55 DEGREES C)
8.6 VOLTAGE TEST AT CORE STAGE
8.7 VOLTAGE TEST ON COMPLETED CABLE
8.8 INSULATION RESISTANCE TEST ON COMPLETED CABLE
8.9 MEASUREMENT OF DIAMETER
9 PRODUCT CONFORMANCE CERTIFICATION (PCC)
Specifies the requirements for cables, telephone, for field use by the Ministry of Defence.
| DevelopmentNote |
Supersedes DEFSTAN 61-12(PT12)SEC3/1(1980). (05/2008) This standard is obsolescent because it is no longer required for the procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (04/2015)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Withdrawn
|
| Supersedes |
| BS 381C:1996 | Specification for colours for identification, coding and special purposes |
| BS 6234:1987 | Specification for polyethylene insulation and sheath of electric cables |
| BS 4109:1970 | Specification for copper for electrical purposes. Wire for general electrical purposes and for insulated cables and flexible cords |
| BS 6004:2000 | Electric cables. PVC insulated, non-armoured cables for voltages up to and including 450/750 V, for electric power, lighting and internal wiring |
| BS 2056:1991 | Specification for stainless steel wire for mechanical springs |
| BS EN 10244-2:2009 | Steel wire and wire products. Non-ferrous metallic coatings on steel wire Zinc or zinc alloy coatings |
| BS 6746:1990 | Specification for PVC insulation and sheath of electric cables |
| BS EN 60068-2-54:2006 | Environmental testing Tests - Test Ta: Solderability testing of electronic components by the wetting balance method |
| BS 6899:1991 | Specification for rubber insulation and sheath of electric cables |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.