DEFSTAN 13-92/3(1996) : 1996
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MANUFACTURE, INSPECTION AND PROOF OF ORDNANCE OF 20 MM CALIBRE AND OVER
Hardcopy , PDF
05-20-2005
DEFSTAN 05-101(PT1)/1(2005) : 2005
DEFSTAN 05-101(PT2)/1(2005) : 2005
DEFSTAN 05-101(PT3)/1(2005) : 2005
English
01-01-1996
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Preface
Section One - General
1 Scope
2 WARNING
3 Related Documents
4 Definitions
Section Two - Manufacture
5 Material
6 Construction
7 Testing
8 Inspection Before Assembly
9 Departure from Design
10 Concentricity and Straightness
11 Pressing
12 Breech Mechanisms
13 Interchangeability
Section Three - Inspection and Examination
14 Requirement
15 Bore and Chamber
16 Limits of Acceptance
17 Surface Treatments
Section Four - Proof of Ordnance
18 Proof Requirements
19 Preparation
20 Proof Data Requirement
21 Proof Pressures
22 Rounds to be Fired
23 Projectiles
24 The Firing of Additional Rounds
25 Variations and Exceptions
26 Submission for Reproof
Section Five - Identification
27 Forging Numbers
28 Registered Numbers
29 Other Markings
30 Marking and Badging
Annex A - Bore Alignment and Measurement Limits
Annex B - Charges to be Fired at Proof of Ordnance or
Associated Parts
Annex C - Service Ordnance Proof Pressures
Annex D - Markings on Ordnance
Gives the conditions governing the manufacture of ordnance and associated components.
| DevelopmentNote |
Supersedes DEFSTAN 13-92/2(1984) (06/2001) This standard is obsolescent because it is no longer required for procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (05/2016)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| DEFSTAN 05-61(PT17)/1(1992) : 1992 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 17: PROOF OF EXPLOSIVE OPERATED DEVICES THAT DISCHARGE PROJECTILES |
| DEFSTAN 05-101(PT1)/1(2005) : 2005 | PROOF OF ORDNANCE, MUNITIONS, ARMOUR AND EXPLOSIVES - PART 1: REQUIREMENTS |
| DEFSTAN 10-13/3(1999) : 1999 | STEEL FORGINGS FOR GUNS |
| DEFSTAN 10-13/4(2005) : 2005 | STEEL FORGINGS FOR GUNS |
| DEFSTAN 07-85(PT1)/3(2006) : 2006 | DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS |
| DEFSTAN 05-101(PT2)/1(2005) : 2005 | PROOF OF ORDNANCE, MUNITIONS, ARMOUR AND EXPLOSIVES - PART 2: GUIDANCE |
| DEFSTAN 07-085(PT1)/4(2017) : 2017 | DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS |
| DEFSTAN 05-61(PT11)/2(1992) : 1992 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 11: PROOF SENTENCING |
| DEFSTAN 05-61(PT14)/1(1994) : 1994 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 14: PROOF SCHEDULES FOR CONVENTIONAL WEAPONS, AMMUNITION AND EXPLOSIVE ITEMS OF NEW MANUFACTURE |
| STANAG 4224 : 2007 | LARGE CALIBRE ARTILLERY AND NAVAL GUN AMMUNITION GREATER THAN 40 MM, SAFETY AND SUITABILITY FOR SERVICE EVALUATION |
| DEFSTAN 05-61(PT1)/3(1998) : 1998 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 1: DEVIATION/PRODUCTION PERMITS AND WAIVERS/CONCESSIONS - QUALITY ASSURANCE OF SUBCONTRACT WORK |
| DEFSTAN 13-36(PT8)/1(1991) : INTERIM | BALLISTIC STANDARDIZATION OF GUN AMMUNITION - PART 8: CRUSHERS AND CRUSHER GAUGES |
| DEFSTAN 05-61(PT14)/1(1994) : 1994 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 14: PROOF SCHEDULES FOR CONVENTIONAL WEAPONS, AMMUNITION AND EXPLOSIVE ITEMS OF NEW MANUFACTURE |
| BS 3811:1993 | Glossary of terms used in terotechnology |
| BS 4778(1979) : LATEST | QUALITY VOCABULARY |
| DEFSTAN 10-13/3(1999) : 1999 | STEEL FORGINGS FOR GUNS |
| STANAG 4225 : 0 | THE SAFETY EVALUATION OF MORTAR BOMBS |
| STANAG 4110 : 2005 | DEFINITIONS OF PRESSURE TERMS AND THEIR INTERRELATIONSHIP FOR USE IN THE DESIGN AND PROOF OF CANNONS OR MORTARS AND AMMUNITION |
| DEFSTAN 05-61(PT11)/2(1992) : 1992 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 11: PROOF SENTENCING |
| DEFSTAN 05-61(PT13)/1(1994) : 1994 | QUALITY ASSURANCE PROCEDURAL REQUIREMENTS - PART 13: ACCEPTANCE PROCEDURES FOR PROOF EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.