DEFSTAN 03-11/4(2003) : 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PHOSPHATE TREATMENT OF IRON AND STEEL
01-22-2008
01-12-2013
Content
Preface
Main Text
SECTION 1 GENERAL REQUIREMENTS
0 Introduction
1 Scope
2 Warning
3 Related Documents
4 Definitions
5 Information to be Supplied to the Processor
6 Process Control
SECTION 2 PROCESS REQUIREMENTS
7 General
8 Heat Treatment
9 Surface Preparation
10 Phosphate Treatment
11 Washing
12 Staining
13 Drying
14 Heat Treatment Relief of Hydrogen Embrittlement
15 Sealing
SECTION 3 INSPECTION AND TEST
16 Inspection
17 Selection of Test Samples
18 Visual Inspection
19 Test for the Presence of a Coating
20 Coating Weight
21 Freedom from Corrosive Residues
22 Resistance to Salt Spray
23 Re-treatment of Items Rejected on Inspection
Annex A Determination of Rinse Water Contamination
Annex B Phosphating of High Strength Steels
Annex C Determination of Phosphate Coating Weight
Annex D Determination of the Freedom from Corrosive Residues
Annex E Salt Droplet Test
Specifies requirements for the processing of iron and steel (excluding corrosion-resisting steels) to produce coatings consisting essentially of inorganic phosphates, which are intended to be used in conjunction with supplementary finishes for the protection of the basis metal against corrosion (and in certain cases to give, additionally, anti-wear properties to sliding surfaces).
| DevelopmentNote |
Supersedes DEFSTAN 03-11/3(1995). (04/2004)
|
| DocumentType |
Standard
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| DEFSTAN 00-970(PT0)/6(2010) : 2010 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 03-4/5(2006) : 2006 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 03-32(PT4)/4(2005) : 2005 | PRE-TREATMENT AND PAINTING OF VEHICLES, ENGINEERING EQUIPMENT AND COMPONENTS - PART 4: SYSTEMS FOR FERROUS METAL, EXCLUDING ARMOUR |
| DEFSTAN 03-32(PT6)/4(2005) : 2005 | PRE-TREATMENT AND PAINTING OF VEHICLES, ENGINEERING EQUIPMENT AND COMPONENTS - PART 6: SYSTEMS FOR SPECIALISED VEHICLES, COMPONENTS AND SUBSTRATES INCLUDING DISTINCTIVE COLOURS |
| DEFSTAN 03-2/4(2005) : 2005 | CLEANING AND PREPARATION OF METAL SURFACES |
| DEFSTAN 02-862(PT4)/2(2007) : 2007 | FASTENERS - PART 4: FERROUS (SUBMARINE FIRST LEVEL QUALITY ASSURED) |
| DEFSTAN 21-5/2(2004) : 2004 | CODE OF PRACTICE FOR PROTECTIVE FINISHES |
| DEFSTAN 00-970(PT0)/5(2007) : 2007 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| BS SP 166:1982 | Specification for spring retaining rings for aerospace application: carbon steel circlips (metric series) |
| BS A287,A288,A289,A290,A291,A292(1982) : 1982 | SPECIFICATION FOR HEXAGON SOCKET HEAD CAP SCREWS - METRIC SERIES |
| DEFSTAN 80-25/4(1997) : 1997 | PAINT, AMMUNITION FINISHING, STOVING SPRAYING AND DIPPING TYPES: SEMI-GLOSS MATT |
| BS EN ISO 6507-1:2005 | Metallic materials. Vickers hardness test Test method |
| DEFSTAN 03-4/4(1998) : 1998 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 91-40/3(2002) : 2002 | CORROSION PREVENTIVE OIL: AIRCRAFT ENGINE, PISTON, METALLIC NATO CODE: C-615 JOINT SERVICE DESIGNATION: PX-27 |
| DEFSTAN 03-29/3(2002) : 2002 | PROTECTION OF METALLIC SPRINGS AGAINST CORROSION |
| BS EN ISO 4536:1995 | Metallic and non-organic coatings on metallic substrates. Saline droplets corrosion test (SD test) |
| DEFSTAN 68-10/5(2003) : 2003 | CORROSION PREVENTIVE: WATER DISPLACING NATO CODE: C-634 JOINT SERVICE DESIGNATION: PX-24 |
| DEFSTAN 80-92/2(1992) : 1992 | LACQUER, PHENOL-FORMALDEHYDE, STOVING, TYPE QX, GRADES 22%, 30%, 39A% - TYPES: DIPPING, SPRAYING |
| DEFSTAN 80-44/2(1997) : 1997 | LACQUER, SHELLAC, TYPE QX - GRADES: 40%, 30%, 20%, 14.5%, 11%, 6% |
| DEFSTAN 80-56/2(1995) : 1995 | PAINT, FINISHING EPOXIDE, STOVING, BLACK FOR SMALL ARMS, SPRAYING |
| DEFSTAN 80-27/4(1998) : 1998 | PAINT, AMMUNITION FINISHING, BRUSHING, SPRAYING AND DIPPING TYPES: SEMI GLOSS MATT |
| BS 3900-F4:1968 | Methods of test for paints Resistance to continuous salt spray |
| DEFSTAN 80-34/3(1995) : 1995 | CORROSION PREVENTIVE, OIL, THIN FILM JOINT SERVICE DESIGNATION: PX-4 |
| DEFSTAN 03-2/3(1995) : 1995 | CLEANING AND PREPARATION OF METAL SURFACES |
| DEFSTAN 80-114/1(1985) : 1985 | PAINT, PRIMING, DEFENCE EQUIPMENT AIR DRYING - TYPES: BRUSHING, SPRAYING DIPPING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.