CSA ISO/IEC 15415:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFORMATION TECHNOLOGY - AUTOMATIC IDENTIFICATION AND DATA CAPTURE TECHNIQUES - BAR CODE SYMBOL PRINT QUALITY TEST SPECIFICATION - TWO-DIMENSIONAL SYMBOLS
Hardcopy , PDF
07-21-2021
English
01-01-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Quality grading
6 Measurement methodology for two-dimensional
multi-row bar code symbols
7 Measurement methodology for two-dimensional
matrix symbols
8 Measurement methodologies for composite
symbologies
9 Substrate characteristics
Annex A (normative) - Symbology-specific parameters and
values for symbol grading
Annex B (informative) - Symbol grading flowchart for
two-dimensional matrix symbols
Annex C (informative) - Interpreting the scan and symbol
grades
Annex D (informative) - Guidance on selection of grading
parameters in application specifications
Annex E (informative) - Substrate characteristics
Annex F (informative) - Parameter grade overlay applied
to two-dimensional symbologies
Bibliography
Specifies: - two methodologies for the measurement of specific attributes of two-dimensional bar code symbols, one of these being applicable to multi-row bar code symbologies and the other to two-dimensional matrix symbologies; - methods for evaluating and grading these measurements and deriving an overall assessment of symbol quality; - information on possible causes of deviation from optimum grades to assist users in taking appropriate corrective action.
| DocumentType |
Standard
|
| Pages |
62
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO/IEC 15415:2011 | Identical |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| ISO/IEC 16022:2006 | Information technology — Automatic identification and data capture techniques — Data Matrix bar code symbology specification |
| ISO/IEC 16023:2000 | Information technology International symbology specification MaxiCode |
| ISO/IEC 18004:2015 | Information technology — Automatic identification and data capture techniques — QR Code bar code symbology specification |
| ISO/IEC 15426-2:2015 | Information technology — Automatic identification and data capture techniques — Bar code verifier conformance specification — Part 2: Two-dimensional symbols |
| ISO/IEC TR 19782:2006 | Information technology Automatic identification and data capture techniques Effects of gloss and low substrate opacity on reading of bar code symbols |
| ISO 7724-2:1984 | Paints and varnishes Colorimetry Part 2: Colour measurement |
| ISO/IEC 15416:2016 | Automatic identification and data capture techniques — Bar code print quality test specification — Linear symbols |
| ISO/IEC 24723:2010 | Information technology — Automatic identification and data capture techniques — GS1 Composite bar code symbology specification |
| EN 12323:2005 | AIDC technologies - Symbology specifications - Code 16K |
| ISO/IEC 15426-1:2006 | Information technology Automatic identification and data capture techniques Bar code verifier conformance specification Part 1: Linear symbols |
| ISO/IEC 19762-1:2008 | Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Part 1: General terms relating to AIDC |
| ISO/IEC 24724:2011 | Information technology — Automatic identification and data capture techniques — GS1 DataBar bar code symbology specification |
| ISO 2859-10:2006 | Sampling procedures for inspection by attributes Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes |
| AIM BC6 : 1995(R2000) | UNIFORM SYMBOLOGY SPECIFICATION - CODE 49 |
| ISO/IEC TR 29158:2011 | Information technology Automatic identification and data capture techniques Direct Part Mark (DPM) Quality Guideline |
| ISO 3951-3:2007 | Sampling procedures for inspection by variables Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection |
| ISO/IEC 19762-2:2008 | Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Part 2: Optically readable media (ORM) |
| ISO/IEC 24728:2006 | Information technology Automatic identification and data capture techniques MicroPDF417 bar code symbology specification |
| ISO/IEC 24778:2008 | Information technology — Automatic identification and data capture techniques — Aztec Code bar code symbology specification |
| ISO 3951-5:2006 | Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation) |
| ISO/IEC 15438:2015 | Information technology Automatic identification and data capture techniques PDF417 bar code symbology specification |
| ISO 3951-2:2013 | Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.