CSA C61400-3 : 2011 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES
Hardcopy , PDF
04-06-2021
English
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principal elements
6 External conditions
7 Structural design
8 Control and protection system
9 Mechanical systems
10 Electrical system
11 Foundation design
12 Assessment of the external conditions at an offshore
wind turbine site
13 Assembly, installation and erection
14 Commissioning, operation and maintenance
Annex A (informative) - Key design parameters for an
offshore wind turbine
Annex B (informative) - Wave spectrum formulations
Annex C (informative) - Shallow water hydrodynamics
and breaking waves
Annex D (informative) - Guidance on calculation of
hydrodynamic loads
Annex E (informative) - Recommendations for design of
offshore wind turbine support structures with
respect to ice loads
Annex F (informative) - Offshore wind turbine foundation
design
Annex G (informative) - Statistical extrapolation of
operational metocean parameters for ultimate
strength analysis
Annex H (informative) - Corrosion protection
Bibliography
Describes additional requirements for assessment of the external conditions at an offshore wind turbine site and also specifies essential design requirements to ensure the engineering integrity of offshore wind turbines.
| DocumentType |
Standard
|
| Pages |
306
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ISO 19901-6:2009 | Petroleum and natural gas industries — Specific requirements for offshore structures — Part 6: Marine operations |
| IEC 60898:1995 | Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations |
| ISO 3010:2017 | Bases for design of structures — Seismic actions on structures |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| CSA C61400-1 : 2014 | WIND TURBINES - PART 1: DESIGN REQUIREMENTS |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| IEC 61400-24:2010 | Wind turbines - Part 24: Lightning protection |
| ISO 4354:2009 | Wind actions on structures |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 2394:2015 | General principles on reliability for structures |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEC TS 61400-13:2001 | Wind turbine generator systems - Part 13: Measurement of mechanical loads |
| ISO 2533:1975 | Standard Atmosphere |
| ISO 17776:2016 | Petroleum and natural gas industries Offshore production installations Major accident hazard management during the design of new installations |
| ISO 15544:2000 | Petroleum and natural gas industries — Offshore production installations — Requirements and guidelines for emergency response |
| NACE RP 01 76 : 2003 | CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION |
| API 2A : 1986 | RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS |
| ISO 13819-2:1995 | Petroleum and natural gas industries Offshore structures Part 2: Fixed steel structures |
| IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
| CSA ISO 19901-1 : 2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 1: METOCEAN DESIGN AND OPERATING CONSIDERATIONS |
| ISO 19906:2010 | Petroleum and natural gas industries Arctic offshore structures |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60755:2017 | General safety requirements for residual current operated protective devices |
| IEC 61000-6-1:2016 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments |
| ISO 9001:2015 | Quality management systems — Requirements |
| STG 2215 : 1998 | RICHTLINIEN FUER KORROSIONSSCHUTZ FUER SCHIFFE UND SEEBAUWERKE - TEIL 1: "SCHIFF, SEEBAUWERK UND AUSRUESTUNG - NEUBAU" |
| IEC 61000-6-4:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
| ISO 8930:1987 | General principles on reliability for structures List of equivalent terms |
| CSA ISO 9001 : 2016 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS |
| IEC 62305-4:2010 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| IEC 60173:1964 | Colours of the cores of flexible cables and cords |
| CSA ISO 19900 : 2014 | PETROLEUM AND NATURAL GAS INDUSTRIES - GENERAL REQUIREMENTS FOR OFFSHORE STRUCTURES |
| CAN/CSA-ISO 19901-4:17 | Petroleum and natural gas industries — Specific requirements for offshore structures — Part 4: Geotechnical and foundation design considerations (Adopted ISO 19901-4:2016, second edition, 2016-07-15) |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| NORSOK M 501 : REV 6 | SURFACE PREPARATION AND PROTECTIVE COATING |
| IEC 61400-21:2008 | Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.