CSA C61400-1 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WIND TURBINES - PART 1: DESIGN REQUIREMENTS
Hardcopy , PDF
05-21-2019
English
01-01-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principal elements
6 External conditions
7 Structural design
8 Control and protection system
9 Mechanical systems
10 Electrical system
11 Assessment of a wind turbine for site-specific conditions
12 Assembly, installation and erection
13 Commissioning, operation and maintenance
Annex A (normative) - Design parameters for describing
wind turbine class S
Annex B (informative) - Turbulence models
Annex C (informative) - Assessment of earthquake loading
Annex D (informative) - Wake and wind farm turbulence
Annex E (informative) - Prediction of wind distribution for
wind turbine sites by measure-correlate-predict
(MCP) methods
Annex F (informative) - Statistical extrapolation of loads
for ultimate strength analysis
Annex G (informative) - Fatigue analysis using Miner's
rule with load extrapolation .85
Annex H (informative) - Contemporaneous loads
Bibliography
Defines essential design requirements to ensure the engineering integrity of wind turbines.
| DevelopmentNote |
Supersedes CSA F416. (04/2008)
|
| DocumentType |
Standard
|
| Pages |
254
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| C22.2 NO. 206-17 | Lighting poles |
| CSA C61400-3 : 2011 : R2016 | WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES |
| CSA C22.2 No. 272 : 2014 | WIND TURBINE ELECTRICAL SYSTEMS |
| CSA C61400-3 : 2011 | WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| IEC 60038:2009 | IEC standard voltages |
| IEC 60898:1995 | Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations |
| ISO 3010:2017 | Bases for design of structures — Seismic actions on structures |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| IEC 61400-24:2010 | Wind turbines - Part 24: Lightning protection |
| ISO 4354:2009 | Wind actions on structures |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 2394:2015 | General principles on reliability for structures |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
| ISO 2533:1975 | Standard Atmosphere |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
| CSA S37 : 2013 | ANTENNAS, TOWERS, AND ANTENNA-SUPPORTING STRUCTURES |
| IEC TR 60755:2008 | General requirements for residual current operated protective devices |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 81400-4:2005 | Wind turbines Part 4: Design and specification of gearboxes |
| IEC 61400-2:2013 | Wind turbines - Part 2: Small wind turbines |
| IEC 61000-6-1:2016 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 61000-6-4:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
| ISO 8930:1987 | General principles on reliability for structures List of equivalent terms |
| IEC 62305-4:2010 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| IEC 60173:1964 | Colours of the cores of flexible cables and cords |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| ISO 76:2006 | Rolling bearings Static load ratings |
| IEC 61400-21:2008 | Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.