CEI EN 62329-2 : 2007
Current
The latest, up-to-date edition.
HEAT SHRINKABLE MOULDED SHAPES - PART 2: METHODS OF TEST
Hardcopy , PDF
English
01-01-2007
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Test conditions
4 Standard test specimens
5 Dimensions
6 Density
7 Heat shock
8 Bending at low temperature
9 Dimensional stability on storage
10 Tensile strength and elongation at break
11 Secant modulus at 2% elongation
12 Electric strength
13 Volume resistivity after damp heat
14 Permittivity and dissipation factor
15 Resistance to tracking
16 Flammability
17 Oxygen index
18 Copper corrosion (presence of corrosive
volatiles)
19 Colour fastness to light
20 Resistance to selected fluids
21 Long term heat ageing (3000 h)
22 Mass
23 Heat ageing
24 Water absorption
25 Colour stability to heat
26 Smoke index
27 Toxicity index
28 Halogen content
29 Acid gas generation
30 Resistance to mould growth
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Gives methods of test for heat-shrinkable moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for connector/cable terminations and multi-way transitions.
| Committee |
CT 15/112
|
| DevelopmentNote |
Classificazione CEI 15-212. (03/2007)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Current
|
| Standards | Relationship |
| IEC 62329-2:2006 | Identical |
| EN 62329-2:2006 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 3261:1975 | Fire tests — Vocabulary |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| IEC 60216-4-2:2000 | Electrical insulating materials - Thermal endurance properties - Part 4-2: Ageing ovens - Precision ovens for use up to 300 °C |
| IEC 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
| ISO 105-B01:2014 | Textiles Tests for colour fastness Part B01: Colour fastness to light: Daylight |
| IEC 60754-1:2011 | Test on gases evolved during combustion of materials from cables - Part 1: Determination of the halogen acid gas content |
| IEC 62329-1:2005 | Heat shrinkable moulded shapes - Part 1: Definitions and general requirements |
| ISO 846:1997 | Plastics Evaluation of the action of microorganisms |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 60754-2:2011 | Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| IEC 60587:2007 | Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion |
| ISO 105-A02:1993 | Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.