BS ISO 6194-4:2009
Current
The latest, up-to-date edition.
Rotary shaft lip-type seals incorporating elastomeric sealing elements Performance test procedures
Hardcopy , PDF
English
04-30-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
3.1 Terms and definitions
3.2 Symbols
4 Pre-test procedure
5 Dynamic normal-temperature test
5.1 Test apparatus
5.2 Installation
5.3 Test conditions
5.4 Test procedure
5.5 Post-test measurements
5.6 Recording
5.7 Acceptance criteria
6 Dynamic low-temperature test
6.1 General
6.2 Test apparatus
6.3 Installation
6.4 Test procedure
6.5 Post-test measurements
6.6 Recording
6.7 Acceptance criteria
7 Material testing of elastomeric components
7.1 Elastomeric material requirements
7.2 Density
7.3 Hardness
7.4 Compression set
7.5 Fluid immersion
7.6 Dry-heat ageing in air
7.7 Stiffness at low temperature
7.8 Recording
8 Identification statement (Reference to this part of
ISO 6194)
Annex A (informative) - Typical example of a seal test
report for the dynamic test
Annex B (informative) - Typical example of a seal test
report for the dynamic low-temperature test
Annex C (informative) - Typical example of an elastomeric
material test report
Bibliography
Describes general test requirements for rotary shaft lip-type seals.
| Committee |
MCE/18/-/3
|
| DevelopmentNote |
Supersedes 97/718034 DC and BS 7780-4(1995). (06/2005) Supersedes 07/30131694 DC. (04/2009)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
ISO6194 describes seals utilizing elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see ISO6194-1:2007, 6.1).
This part of ISO6194 specifies general test requirements for rotary shaft lip-type seals. The tests may be used for qualification purposes.
NOTE ISO6194 is complementary to ISO16589 which covers seals incorporating thermoplastic sealing elements.
| Standards | Relationship |
| ISO 6194-4:2009 | Identical |
| DEFSTAN 08-107/3(2013) : 2013 | GENERAL REQUIREMENTS FOR THE DESIGN OF ELECTROTECHNICAL AND NAVAL WEAPON EQUIPMENT |
| DEFSTAN 02-339/2(2002) : INTERIM | REQUIREMENTS FOR STEERING AND STABILIZER SYSTEMS FOR HM SURFACE SHIPS AND ROYAL FLEET AUXILIARIES |
| DEFSTAN 02-339/3(2006) : 2006 | REQUIREMENTS FOR STEERING AND STABILIZER SYSTEMS FOR HM SURFACE SHIPS AND ROYAL FLEET AUXILIARIES |
| ISO 812:2017 | Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness |
| ISO 1432:2013 | Rubber, vulcanized or thermoplastic Determination of low-temperature stiffening (Gehman test) |
| ISO 2921:2011 | Rubber, vulcanized Determination of low-temperature retraction (TR test) |
| ISO 5164:2014 | Petroleum products — Determination of knock characteristics of motor fuels — Research method |
| ISO 6194-2:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 2: Vocabulary |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 815-2:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures |
| ISO 6194-1:2007 | Rotary shaft lip-type seals incorporating elastomeric sealing elements — Part 1: Nominal dimensions and tolerances |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 16589-5:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 5: Identification of visual imperfections |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 16589-1:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 1: Nominal dimensions and tolerances |
| ISO 16589-4:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 4: Performance test procedures |
| ISO 16589-3:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 3: Storage, handling and installation |
| ISO 5163:2014 | Petroleum products — Determination of knock characteristics of motor and aviation fuels — Motor method |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 16589-2:2001 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 2: Vocabulary |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.