BS ISO 23559:2011
Current
The latest, up-to-date edition.
Plastics. Film and sheeting. Guidance on the testing of thermoplastic films
Hardcopy , PDF
English
11-30-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation and conditioning
5 Test requirements
6 Presentation of results
Bibliography
Describes test procedures to assist producers and users in the selection and characterization of thermoplastic films in single- or multi-layer form.
| Committee |
PRI/75
|
| DevelopmentNote |
Supersedes 06/30130313 DC. (03/2008) Reviewed and confirmed by BSI, September 2016. (08/2016)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This International Standard identifies specific test procedures to assist producers and users in the selection and characterization of thermoplastic films in single- or multi-layer form. It is intended to serve as a guide for those films for which there are no existing standards or specifications.
NOTE Because of the range of materials used and the wide variety of processes available to produce various film constructions, this document does not address specimen preparation.
If an International Standard exists for a specific film product, the requirements of that standard shall take precedence over this document.
There are many national, regional and industrial standards that address the requirements for specific applications. Since this International Standard is intended to provide general guidance, it is not within the scope to address these.
The significance of the data and fitness for use shall be determined by the user.
| Standards | Relationship |
| ISO 23559:2007 | Identical |
| ISO 23559:2011 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 15106-2:2003 | Plastics — Film and sheeting — Determination of water vapour transmission rate — Part 2: Infrared detection sensor method |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 11443:2014 | Plastics Determination of the fluidity of plastics using capillary and slit-die rheometers |
| ISO 9773:1998 | Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source |
| ASTM D 5748 : 1995 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ISO 13468-1:1996 | Plastics Determination of the total luminous transmittance of transparent materials Part 1: Single-beam instrument |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 7765-1:1988 | Plastics film and sheeting Determination of impact resistance by the free-falling dart method Part 1: Staircase methods |
| ISO 11501:1995 | Plastics Film and sheeting Determination of dimensional change on heating |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 15106-1:2003 | Plastics — Film and sheeting — Determination of water vapour transmission rate — Part 1: Humidity detection sensor method |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| ISO 15105-1:2007 | Plastics Film and sheeting Determination of gas-transmission rate Part 1: Differential-pressure methods |
| ISO 15106-3:2003 | Plastics — Film and sheeting — Determination of water vapour transmission rate — Part 3: Electrolytic detection sensor method |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 15105-2:2003 | Plastics — Film and sheeting — Determination of gas-transmission rate — Part 2: Equal-pressure method |
| ISO 15989:2004 | Plastics — Film and sheeting — Measurement of water-contact angle of corona-treated films |
| ISO 13468-2:1999 | Plastics Determination of the total luminous transmittance of transparent materials Part 2: Double-beam instrument |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 307:2007 | Plastics Polyamides Determination of viscosity number |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ISO 7765-2:1994 | Plastics film and sheeting Determination of impact resistance by the free-falling dart method Part 2: Instrumented puncture test |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 8295:1995 | Plastics Film and sheeting Determination of the coefficients of friction |
| ISO 6383-2:1983 | Plastics Film and sheeting Determination of tear resistance Part 2: Elmendorf method |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 8296:2003 | Plastics — Film and sheeting — Determination of wetting tension |
| ISO 4592:1992 | Plastics — Film and sheeting — Determination of length and width |
| ISO 11502:1995 | Plastics Film and sheeting Determination of blocking resistance |
| ISO 4589-1:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 1: General requirements |
| ISO 6383-1:2015 | Plastics Film and sheeting Determination of tear resistance Part 1: Trouser tear method |
| ISO 14782:1999 | Plastics Determination of haze for transparent materials |
| ISO 2813:2014 | Paints and varnishes — Determination of gloss value at 20°, 60° and 85° |
| ISO 4593:1993 | Plastics Film and sheeting Determination of thickness by mechanical scanning |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.