BS ISO 22902-7:2006
Current
The latest, up-to-date edition.
Road vehicles. Automotive multimedia interface Physical specification
Hardcopy , PDF
English
11-30-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Environment
3.1 Mounting location in the vehicle
3.2 Component or device compliance test procedure
3.3 Component or device electromagnetic compatibility
test procedure
3.4 Plastic optical fiber connector test procedure
3.5 IDB 1394 consumer connector port test procedure
3.6 Plastic optical fiber cable (POF) test procedure
3.7 Fiber optic transceiver (FOT) test procedure
4 Power management
4.1 Boundary
4.2 Typical vehicle power characteristics
4.3 Vehicle operational modes
4.4 AMI-C network power mode considerations
4.5 AMI-C network power consumption management
4.6 AMI-C Network power and ground requirements
4.7 AMI-C network components or devices
4.8 Device power mode implementations
4.9 Component or device power consumption states
4.10 AMI-C component or device electrical test procedures
5 Interconnectivity
5.1 Plastic optical fiber connectors
5.2 Plastic optical fiber cable
5.3 Consumer convenience port (CCP)
5.4 RF connector systems
6 Packaging
6.1 Package location
6.2 Specifications for packaging
Annex A (normative) EMC test plan data requirements
Annex B (informative) Informative references
Provides conditions and testing at the equipment level; it does not include all conditions and testing necessary for complete verification and validation of the vehicle system.
| Committee |
AUE/16
|
| DevelopmentNote |
Supersedes 05/30131758 DC (11/2006)
|
| DocumentType |
Standard
|
| Pages |
68
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ISO 22902-7:2006 | Identical |
| SAE USCAR 2 : 2013 | PERFORMANCE SPECIFICATION FOR AUTOMOTIVE ELECTRICAL CONNECTOR SYSTEMS |
| ISO 16750-2:2012 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 2: Electrical loads |
| ISO 16750-4:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 4: Climatic loads |
| ISO 16750-5:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 5: Chemical loads |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| ISO 16750-1:2006 | Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 1: General |
| ISO 7637-1:2015 | Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations |
| TIA/EIA 455-1 : B1998(R2008) | CABLE FLEXING FOR FIBER OPTIC INTERCONNECTING DEVICES |
| ISO 11452-4:2011 | Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Harness excitation methods |
| TIA 455-21 : A1988(R2012) | FOTP-21 MATING DURABILITY FOR FIBER OPTIC INTERCONNECTING DEVICES |
| ISO 7637-2:2011 | Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only |
| IEC 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
| SAE J 1113/12 : 2006 | ELECTRICAL INTERFERENCE BY CONDUCTION AND COUPLING - CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES |
| SAE J 1113/21 : 2013 | ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURE FOR VEHICLE COMPONENTS - PART 21: IMMUNITY TO ELECTROMAGNETIC FIELDS, 30 MHZ TO 18 GHZ, ABSORBER-LINED CHAMBER |
| ISO 8092-2:2005 | Road vehicles — Connections for on-board electrical wiring harnesses — Part 2: Definitions, test methods and general performance requirements |
| CISPR 25:2016 | Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers |
| IEC 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| ISO 6722:2006 | Road vehicles 60 V and 600 V single-core cables Dimensions, test methods and requirements |
| IEC 61300-3-8:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-8: Examinations and measurements - Ambient light susceptibility |
| ISO 16750-3:2012 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 3: Mechanical loads |
| IEC 60793-1-40:2001 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| SAE USCAR 17 : 2013 | PERFORMANCE SPECIFICATION FOR AUTOMOTIVE RF CONNECTOR SYSTEMS |
| TIA/EIA 455-34 : A1995(R2002) | INTERCONNECTION DEVICE INSERTION LOSS TEST |
| IEC 60068-2-28:1990 | Environmental testing - Part 2: Tests. Guidance for damp heat tests |
| SAE USCAR 19 : 2002 | COAXIAL CABLE CONNECTOR INTERFACE - SQUARE OUTER CONDUCTOR |
| SAE USCAR 18 : 2011 | USCAR-17 SUPPLEMENT |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.