BS ISO 22621-6:2010
Current
The latest, up-to-date edition.
Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar). Polyamide (PA) Code of practice for design, handling and installation
Hardcopy , PDF
English
05-31-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Design
6 Installation
7 Storage, handling and transport
8 Quality control
Annex A (informative) - Derating coefficients for operating
temperatures
Describes a code of practice dealing with polyamide (PA) piping systems, intended to be buried outside buildings and used for the supply of gaseous fuels.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 09/30181333 DC. (05/2010)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of ISO22621 specifies a code of practice dealing with polyamide (PA) piping systems, intended to be buried outside buildings and used for the supply of gaseous fuels.
It is applicable to mains and service lines, the components of which are prepared for jointing by scraping and/or machining, and gives instructions for the design, storage, handling, transportation, laying conditions and fusion quality control of PA pipes and fittings up to and including 250mm outside diameter, as well as subsequent joint testing, backfilling, pipe system testing, commissioning and decommissioning.
The jointing methods covered by this part of ISO22621 are butt fusion jointing and electrofusion jointing.
No special precautions are necessary for areas exposed to the influence of mining and earthquakes other than those precautions mentioned in this part of ISO22621.
It is the responsibility of users of this part of ISO22621 to take existing and new national regulations into account.
| Standards | Relationship |
| ISO 22621-6:2010 | Identical |
| EN 12327:2012 | Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
| ISO 22621-2:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 2: Pipes |
| ISO 12176-3:2011 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 3: Operator's badge |
| ISO 22621-3:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 3: Fittings |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 22621-1:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 1: General |
| ISO 22621-5:2010 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 5: Fitness for purpose of the system |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.