BS ISO 17467-1:2012
Current
The latest, up-to-date edition.
Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems jointed by solvent cement General
Hardcopy , PDF
English
11-30-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material
Annex A (normative) - Assessment of the degree of pigment
or carbon black dispersion in unplasticized
polyamide compounds
Annex B (normative) - Chemical resistance
Annex C (informative) - Design guidance
Annex D (normative) - Hoop stress at burst
Bibliography
Describes the general properties of unplasticized polyamide (PA-U) compounds for the manufacturing of pipes, fittings and valves made from such compounds, intended to be buried and used for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 11/30248330 DC. (11/2012)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of ISO17467 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacturing of pipes, fittings and valves made from such compounds, intended to be buried and used for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar.
It also specifies the test parameters for the test methods to which it refers.
This part of ISO17467 specifies a calculation and design scheme on which the maximum operating pressure (MOP) of piping systems is based.
| Standards | Relationship |
| ISO 17467-1:2012 | Identical |
| AS 2944.2-2007 | Plastics pipes and fittings for gas reticulation Polyamide fittings (Reconfirmed 2023) |
| ISO 1874-1:2010 | Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification |
| AS/NZS 4645.3:2008 | Gas distribution networks Plastics pipe systems |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1874-2:2012 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| AS 2943-2007 | Plastics pipes and fittings for gas reticulation - Polyamide compounds (Reconfirmed 2022) |
| ISO 16871:2003 | Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 307:2007 | Plastics Polyamides Determination of viscosity number |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ASTM F 1733 : 2013 : REDLINE | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 17467-2:2012 | Plastics piping systems for the supply of gaseous fuels Unplasticized polyamide (PA-U) piping systems jointed by solvent cement Part 2: Pipes |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13480:1997 | Polyethylene pipes Resistance to slow crack growth Cone test method |
| ISO 6259-3:2015 | Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| AS 2944.1-2007 | Plastics pipes and fittings for gas reticulation Polyamide pipes (Reconfirmed 2023) |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.