BS ISO 16924 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
NATURAL GAS FUELLING STATIONS - LNG STATIONS FOR FUELLING VEHICLES
Hardcopy , PDF
04-30-2018
English
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Risk management
6 General design requirements
7 Fuel supply to the fuelling station
8 Storage
9 Pumps and compressors
10 Dispensers
11 Vaporizers and heaters
12 Odorization
13 Pipework
14 Electrical equipment and wiring
15 Instrumentation and control system
16 Emergency shutdown
17 Special configurations
18 Testing and commissioning
19 Operations
20 Inspection and maintenance
Annex A (informative) - Examples of hazardous zones
classification
Annex B (normative) - Separation distances
Annex C (informative) - Example flow diagram of an LNG
fuelling station
Annex D (informative) - Example flow diagram of an LCNG
fuelling station
Annex E (informative) - Example flow diagram of an LNG
and LCNG fuelling station
Annex F (informative) - Process requirements for the effective
cryogenic pump operation
Annex G (informative) - Recommendations for installation of
a centrifugal pump
Annex H (informative) - Recommendations for centrifugal pump
design
Annex I (informative) - Recommendations for installation of
a reciprocating pump
Annex J (informative) - Recommendations on the content of
the cryogenic pump operation instructions
Annex K (informative) - Example flow diagram of a
high-pressure odorizer
Annex L (informative) - LNG identification mark of an LNG
fuelling station
Bibliography
Defines the design, construction, operation, maintenance and inspection of stations for fuelling liquefied natural gas (LNG) to vehicles, including equipment, safety and control devices.
| Committee |
GSE/40
|
| DevelopmentNote |
Supersedes 13/30271407 DC. (12/2016) Renumbered and superseded by BS EN ISO 16924. (05/2018)
|
| DocumentType |
Standard
|
| Pages |
90
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| Supersedes |
| ISO 15649:2001 | Petroleum and natural gas industries — Piping |
| ISO 12991:2012 | Liquefied natural gas (LNG) — Tanks for on-board storage as a fuel for automotive vehicles |
| ISO 20421-2:2017 | Cryogenic vessels Large transportable vacuum-insulated vessels Part 2: Operational requirements |
| ISO 21013-3:2016 | Cryogenic vessels Pressure-relief accessories for cryogenic service Part 3: Sizing and capacity determination |
| ISO 21013-1:2008 | Cryogenic vessels Pressure-relief accessories for cryogenic service Part 1: Reclosable pressure-relief valves |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| ISO 21010:2014 | Cryogenic vessels Gas/materials compatibility |
| ISO 21011:2008 | Cryogenic vessels — Valves for cryogenic service |
| IEC 60079-19:2010+AMD1:2015 CSV | Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation |
| IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| API 685 : 2011 | SEALLESS CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL, AND GAS INDUSTRY PROCESS SERVICE |
| ISO 12617:2015 | Road vehicles Liquefied natural gas (LNG) refuelling connector 3,1 MPa connector |
| ISO 21029-2:2015 | Cryogenic vessels Transportable vacuum insulated vessels of not more than 1 000 litres volume Part 2: Operational requirements |
| ISO 31000:2009 | Risk management Principles and guidelines |
| 2004/22/EC : 2004 | DIRECTIVE 2004/22/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 31 MARCH 2004 ON MEASURING INSTRUMENTS |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO/TR 15403-2:2006 | Natural gas - Natural gas for use as a compressed fuel for vehicles Part 2: Specification of the quality |
| ISO 21009-2:2015 | Cryogenic vessels — Static vacuum insulated vessels — Part 2: Operational requirements |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| IEC 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| API 2003 : 2015 | PROTECTION AGAINST IGNITIONS ARISING OUT OF STATIC, LIGHTNING, AND STRAY CURRENTS |
| ISO 21014:2006 | Cryogenic vessels Cryogenic insulation performance |
| ISO 15609-3:2004 | Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 3: Electron beam welding |
| EN 13645:2001 | Installations and equipment for liquefied natural gas - Design of onshore installations with a storage capacity between 5 t and 200 t |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 13686:2013 | Natural gas Quality designation |
| ISO/TS 16922:2002 | Natural gas Guidelines for odorizing gases |
| ISO 15403-1:2006 | Natural gas Natural gas for use as a compressed fuel for vehicles Part 1: Designation of the quality |
| ISO 21028-1:2016 | Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 1: Temperatures below -80 degrees C |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| ISO 14532:2014 | Natural gas — Vocabulary |
| ISO 21028-2:2004 | Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 2: Temperatures between -80 degrees C and -20 degrees C |
| NFPA 52 : 2016 | VEHICULAR NATURAL GAS FUEL SYSTEMS CODE |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| ISO 24490:2016 | Cryogenic vessels Pumps for cryogenic service |
| CGA S 1.2 : 2009 | PRESSURE RELIEF DEVICE STANDARDS - PART 2: PORTABLE CONTAINERS FOR COMPRESSED GASES |
| IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
| ISO 13709:2009 | Centrifugal pumps for petroleum, petrochemical and natural gas industries |
| ISO 15609-2:2001 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding |
| ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding |
| NFPA 77 : 2014 | STATIC ELECTRICITY |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| ISO 20421-1:2006 | Cryogenic vessels Large transportable vacuum-insulated vessels Part 1: Design, fabrication, inspection and testing |
| ISO 21013-2:2007 | Cryogenic vessels Pressure-relief accessories for cryogenic service Part 2: Non-reclosable pressure-relief devices |
| ISO 21029-1:2004 | Cryogenic vessels Transportable vacuum insulated vessels of not more than 1 000 litres volume Part 1: Design, fabrication, inspection and tests |
| CGA S 1.3 : 2008 | PRESSURE RELIEF DEVICE STANDARDS - PART 3: STATIONARY STORAGE CONTAINERS FOR COMPRESSED GASES |
| ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding |
| ISO 21009-1:2008 | Cryogenic vessels — Static vacuum-insulated vessels — Part 1: Design, fabrication, inspection and tests |
| ISO 23208:2017 | Cryogenic vessels — Cleanliness for cryogenic service |
| ISO 21012:2006 | Cryogenic vessels Hoses |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| NFPA 497 : 2017 | CLASSIFICATION OF FLAMMABLE LIQUIDS, GASES, OR VAPORS AND OF HAZARDOUS (CLASSIFIED) LOCATIONS FOR ELECTRICAL INSTALLATIONS IN CHEMICAL PROCESS AREAS |
| ISO 15609-6:2013 | Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 6: Laser-arc hybrid welding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.