BS EN ISO 3650:1999
Current
The latest, up-to-date edition.
Geometrical product specifications (GPS). Length standards. Gauge blocks
Hardcopy , PDF
English
05-15-1999
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Nomenclature of faces
5 Basis of measurement, traceability, reference condition
6 General dimensions, material properties, marking
7 Metrological requirements
8 Calibration of gauge blocks
Annex A (informative) - Example of a device for the
comparison of gauge blocks
Annex B (informative) - Relation to the GPS matrix model
Annex C (informative) - Bibliography
Annex ZA (normative) - Normative references to international
publications with their relevant European publications
Defines the most important design and metrological characteristics of gauge blocks with a rectangular cross section and a nominal length l[n] ranging from 0,5 mm to 1000 mm.
| Committee |
TPR/1
|
| DevelopmentNote |
Supersedes BS 4311-1(1993) and 96/704405 DC. (10/2005)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This International Standard specifies the most important design and metrological characteristics of gauge blocks with a rectangular cross section and a nominal length ln ranging from 0,5mm to 1000mm.
Limit deviations and tolerances are stated for the calibration gradeK and for the grades 0, 1 and 2 for various measuring purposes.
| Standards | Relationship |
| EN ISO 3650:1998 | Identical |
| SN EN ISO 3650 : 1999 | Identical |
| NF EN ISO 3650 : 1999 | Identical |
| ISO 3650:1998 | Identical |
| I.S. EN ISO 3650:1999 | Identical |
| UNI EN ISO 3650 : 2002 | Identical |
| NBN EN ISO 3650 : 1999 COR 2009 | Identical |
| NEN EN ISO 3650 : 1999 | Identical |
| NS EN ISO 3650 : 1998 AC 2009 | Identical |
| DIN EN ISO 3650:1999-02 | Identical |
| BS 4311-1:2007 | Gauge blocks manufactured to imperial specification Specification and validation |
| BS 1643:2008 | Specification for precision vernier height gauges |
| BS 1726-2:2002 | Cylindrical helical springs made from round wire and bar. Guide to methods of specifying, tolerances and testing Extension springs |
| BS 4311-2:2009 | Gauge blocks manufactured to imperial specification Accessories |
| BS 6468:2008 | Specification for depth micrometers |
| 09/30193117 DC : 0 | BS 4311-2 - GAUGE BLOCKS MANUFACTURED TO IMPERIAL SPECIFICATION - PART 2: ACCESSORIES |
| BS 1726-1:2002 | Cylindrical helical springs made from round wire and bar. Guide to methods of specifying, tolerances and testing Compression springs |
| BS 1726-1:2010 | Cylindrical helical springs made from round wire and bar. Guide to methods of specifying and tolerancing hot coiled springs, and cold coiled springs not covered by BS EN 15800, and general spring testing Compression springs |
| BS 8726-1:2002 | Cylindrical helical springs made from rectangular and square section wire and bar. Guide to calculation and design Compression springs |
| BS 4311(2007) : 2007 | GAUGE BLOCKS MANUFACTURED TO IMPERIAL SPECIFICATION - SPECIFICATION, VALIDATION AND ACCESSORIES |
| 10/30205484 DC : 0 | BS 1726-1 - CYLINDRICAL HELICAL SPRINGS MADE FROM ROUND WIRE AND BAR - GUIDE TO METHODS OF SPECIFYING TOLERANCES FOR HOT COILED SPRINGS, AND COLD COILED SPRINGS NOT COVERED BY BS EN 15800 - GENERAL SPRING TESTING - PART 1: COMPRESSION SPRINGS |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1:2016 | Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.