BS EN ISO 18595:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Resistance welding. Spot welding of aluminium and aluminium alloys. Weldability, welding and testing
Hardcopy , PDF
02-16-2021
English
09-28-2007
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Material
5.1 Form
5.2 Types of aluminium alloys
6 Surface conditions
7 Edge distance, edge conditions, form of component
and weld spacing
8 Electrodes
8.1 Materials
8.2 Dimensions
8.3 Cooling electrodes
9 Weld assessment
9.1 General
9.2 Weldability test procedure
9.3 Procedure qualification tests
9.4 Production tests
9.5 Frequency of testing
10 Weld quality requirements
10.1 Weld diameter
10.2 Weld dimensions
10.3 Weld fracture mode
10.4 Weld strength
10.5 Weld appearance - Surface condition
11 Multi-weld arrays
Annex A (informative) Recommendations for spot welding
equipment
Annex B (informative) Typical spot welding conditions
Annex C (informative) Non-exhaustive list of aluminium alloys
covered by this International Standard
Annex D (informative) Typical information to appear on a welding
procedure sheet for spot welding
Bibliography
Specifies requirements for resistance spot welding in the fabrication of assemblies of aluminium sheet, extrusions (both work- and age-hardening alloys) and/or cast material comprising two or three thicknesses of metal, where the maximum single (sheet) thickness of components to be welded is within the range 0,6 mm to 6 mm.
| Committee |
WEE/29
|
| DevelopmentNote |
Supersedes 06/30131171 DC. (09/2007) Reviewed and confirmed by BSI, September 2010. (08/2010)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN ISO 18595 : 2008 | Identical |
| SN EN ISO 18595 : 2007 | Identical |
| NS EN ISO 18595 : 1ED 2007 | Identical |
| ISO 18595:2007 | Identical |
| DIN EN ISO 18595:2007-12 | Identical |
| NEN EN ISO 18595 : 2007 | Identical |
| I.S. EN ISO 18595:2007 | Identical |
| NF EN ISO 18595 : 2007 | Identical |
| EN ISO 18595:2007 | Identical |
| UNI EN ISO 18595 : 2008 | Identical |
| ISO 5182:2016 | Resistance welding Materials for electrodes and ancillary equipment |
| ISO 14373:2015 | Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels |
| ISO 10447:2015 | Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds |
| ISO 5830:1984 | Resistance spot welding Male electrode caps |
| ISO 15614-12:2014 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 12: Spot, seam and projection welding |
| ISO 669:2016 | Resistance welding Resistance welding equipment Mechanical and electrical requirements |
| ISO 14329:2003 | Resistance welding Destructive tests of welds Failure types and geometric measurements for resistance spot, seam and projection welds |
| ISO 5184:1979 | Straight resistance spot welding electrodes |
| ISO 5821:2009 | Resistance welding — Spot welding electrode caps |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.