BS EN ISO 11403-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics. Acquisition and presentation of comparable multipoint data Mechanical properties
Hardcopy , PDF
07-09-2021
English
08-31-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation
5 Conditioning
6 Test requirements
7 Presentation of data
8 Precision
Bibliography
Defines test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics: - dynamic modulus; - tensile properties at constant test speed; - ultimate stress and strain; - tensile stress-strain curves; - tensile creep; - Charpy impact strength; and - puncture impact behaviour.
| Committee |
PRI/21
|
| DevelopmentNote |
Renumbers and Supersedes BS ISO 11403-1 2000 Version incorporates amendment 10683 to BS ISO 11403-1 (08/2000) Supersedes 00/121932 DC. (05/2003) Supersedes 12/30255180 DC. (06/2014)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN ISO 11403-1 : 2014 | Identical |
| DIN EN ISO 11403-1:2003-09 | Identical |
| DIN EN ISO 11403-1:2014-09 | Identical |
| EN ISO 11403-1:2014 | Identical |
| UNI EN ISO 11403-1 : 2014 | Identical |
| I.S. EN ISO 11403-1:2014 | Identical |
| NF EN ISO 11403-1 : 2014 | Identical |
| NS EN ISO 11403-1 : 2014 | Identical |
| SN EN ISO 11403-1 : 2014 | Identical |
| NEN EN ISO 11403-1 : 2014 | Identical |
| NBN EN ISO 11403-1 : 2014 | Identical |
| UNE-EN ISO 11403-1:2014 | Identical |
| ISO 11403-1:2014 | Identical |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 15850:2014 | Plastics — Determination of tension-tension fatigue crack propagation — Linear elastic fracture mechanics (LEFM) approach |
| ISO 6721-2:2008 | Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 17281:2002 | Plastics Determination of fracture toughness (GIC and KIC) at moderately high loading rates (1 m/s) |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 6721-4:2008 | Plastics Determination of dynamic mechanical properties Part 4: Tensile vibration Non-resonance method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 13586:2000 | Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.