BS EN 62109-1:2010

FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 General testing requirements
5 Marking and documentation
6 Environmental requirements and conditions
7 Protection against electric shock and energy hazards
8 Protection against mechanical hazards
9 Protection against fire hazards
10 Protection against sonic pressure hazards
11 Protection against liquid hazards
12 Chemical hazards
13 Physical requirements
14 Components
15 Software and firmware performing safety functions
Annex A (normative) - Measurement of clearances and creepage
        distances
Annex B (normative) - Programmable equipment
Annex C (normative) - Symbols to be used in equipment markings
Annex D (informative) - Test probes for determining access
Annex E (informative) - RCDs
Annex F (informative) - Altitude correction for clearances
Annex G (informative) - Clearance and creepage distance
        determination for frequencies greater than 30 kHz
Annex H (informative) - Measuring instrument for touch current
        measurements
Annex I (informative) - Examples of protection, insulation, and
        overvoltage category requirements for PCE
Annex J (normative) - Ultraviolet light conditioning test
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Pertains to the power conversion equipment (PCE) for use in Photovoltaic (PV) systems where a uniform technical level with respect to safety is necessary.

1.1 Scope This part of IEC 62109 applies to the power conversion equipment (PCE) for use in Photovoltaic (PV) systems where a uniform technical level with respect to safety is necessary. This standard defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire, mechanical and other hazards. This standard provides general requirements applicable to all types of PV PCE. There are additional parts of this standard that provide specific requirements for the different types of power converters, such as Part 2-inverters. Additional parts may be published as new products and technologies are commercialised. 1.1.1 Equipment included in scope This standard covers PCE connected to systems not exceeding maximum PV source circuit voltage of 1 500 V d.c. The equipment may also be connected to systems not exceeding 1 000 V a.c. at the a.c. mains circuits, non-mains a.c. load circuits, and to other DC source or load circuits such as batteries. This standard may be used for accessories for use with PCE, except where more appropriate standards exist. Evaluation of PCE to this standard includes evaluation of all features and functions incorporated in or available for the PCE, or referred to in the documentation provided with the PCE, if such features or functions can affect compliance with the requirements of this standard. 1.1.2 Equipment for which other requirements may apply This standard has not been written to address characteristics of power sources other than photovoltaic systems, such as wind turbines, fuel cells, rotating machine sources, etc. NOTE 1 Requirements for other sources may be incorporated in the IEC 62109 series in the future. Additional or other requirements are necessary for equipment intended for use in explosive atmospheres (see IEC 60079), aircraft, marine installations, electromedical applications (see IEC 60601) or at elevations above 2 000 m. NOTE 2 Requirements are included for adjustment of clearance distances for higher elevations, but not for other factors related to elevation, such as thermal considerations 1.2 Object 1.2.1 Aspects included in scope The purpose of the requirements of this part of IEC 62109 is to ensure that the design and methods of construction used provide adequate protection for the operator and the surrounding area against: electric shock and energy hazards; mechanical hazards; excessive temperature hazards; spread of fire from the equipment; chemical hazards; sonic pressure hazards; liberated fluids, gases and explosion hazards. NOTE Servicing personnel are expected to have the necessary knowledge and skill to use reasonable care in dealing with hazards associated with the operation, repair and maintenance of this equipment. Based upon this premise, this standard provides only limited requirements (for example markings or guarding) intended to protect service personnel from hazards that may not be apparent even to trained personnel. 1.2.2 Aspects excluded from scope Aspects not covered by this standard include, but are not limited to, the following: functional reliability, performance or other properties of the equipment not related to safety; effectiveness of transport packaging; EMC requirements; installation requirements, which are covered by local and national installation codes. NOTE This standard does provide requirements for PCE intended to ensure that the PCE can be installed in a safe manner, including requirements for installation instructions provided with the product.