BS EN 61858:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS
Hardcopy , PDF
05-31-2014
English
03-31-2009
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General considerations
5 Evaluation of the change of thickness of an EIM
5.1 Samples
5.2 Acceptance
6 Substitution of winding wire
6.1 General
6.2 Substitution of enamel
6.3 Substitution of conductor material
6.4 Alternate winding wire
7 Substitution of impregnating resin/varnish
7.1 Thermal class determination
7.2 Evaluation
7.2.1 Thermal classes equal or better
7.2.2 One thermal class lower
7.2.3 Other criteria
8 Substitution with other EIM
8.1 Technically equivalent materials
8.2 Previous evaluation
8.3 Other
9 Evaluation of additions
9.1 Addition of an impregnating resin/varnish
9.2 Addition of other components
10 Single-point thermal ageing test
10.1 Test objects
10.2 Establishing the EIS relative thermal endurance
index (EIS RTE)
10.3 Interpretation of results
Annex A (normative) - Classes of winding wire
Annex B (normative) - Compatibility test procedure
Bibliography
Annex ZA (normative) - Normative references to
international publications with their corresponding
European publications
Provides the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification.
Committee |
GEL/112
|
DevelopmentNote |
Supersedes 98/261261 DC and 03/307567 DC. (04/2005) Supersedes 08/30177151 DC. (04/2009)
|
DocumentType |
Standard
|
Pages |
24
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
IEC 61858:2008 lists the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification. This standard is applicable to EIS used in wire-wound electrotechnical devices. The test procedures are comparative in that the performance of a candidate EIS is compared to that of a reference EIS, which has proven service experience in accordance with IEC 60505 or has been evaluated by one of the procedures given in the IEC 61857 series. This third edition cancels and replaces the second edition, published in 2004 by IEC TC 98: Electrical insulation systems (EIS). It constitutes an editorial revision.
Standards | Relationship |
I.S. EN 61858:2008 | Identical |
UNE-EN 61858:2009 | Identical |
IEC 61858:2008 | Identical |
EN 61858:2008 | Identical |
SN EN 61858 : 2008 | Identical |
DIN EN 61858 : 2009 | Identical |
NBN EN 61858 : 2009 | Identical |
NF EN 61858 : 2009 | Identical |
IEC 60317-3:2004+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 3: Polyester enamelled round copper wire, class 155 |
EN 60317-30:1996/A2:2005 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220 |
IEC 60317-42:1997+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 42: Polyester-amide-imide enamelled round copper wire, class 200 |
IEC 60317-7:1990+AMD1:1997+AMD2:1997 CSV | Specifications for particular types of winding wires - Part 7: Polyimide enamelled round copper wire, class 220 |
IEC 60317-41:1996 | Specifications for particular types of winding wires - Part 41: Solderable polyester enamelled round copper wire, class 130L |
EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
IEC 60317-15:2004+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180 |
IEC 60317-51:2014 | Specifications for particular types of winding wires - Part 51: Solderable polyurethane enamelled round copper wire, class 180 |
HD 555.16 : 200S2 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYESTER ENAMELLED RECTANGULAR COPPER WINDING WIRE, CLASS 155 |
IEC 60317-4:2015 | Specifications for particular types of winding wires - Part 4: Solderable polyurethane enamelled round copper wire, class 130 |
EN 60317-29:1996/A2:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 29: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 200 |
IEC 60317-21:2013 | Specifications for particular types of winding wires - Part 21: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 155 |
IEC 60317-47:2013 | Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240 |
EN 60317-15:2004/A1:2010 | Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180 |
IEC 60317-19:1990+AMD1:1997+AMD2:1999 CSV | Specifications for particular types of winding wires - Part 19: Solderable polyurethane enamelled round copper wire, overcoated with polyamide, class 130 |
IEC 60317-8:2010 | Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180 |
EN 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
EN 60317-46:2014 | Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240 |
IEC 60317-34:1997 | Specifications for particular types of winding wires - Part 34: Polyester enamelled round copper wire, class 130L |
IEC 60317-30:1990 | Specifications for particular types of winding wires. Part 30: Polyimide enamelled rectangular copper wire, class 220 |
IEC 60505:2011 | Evaluation and qualification of electrical insulation systems |
IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
IEC 60317-23:2013 | Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180 |
IEC 60317-24:1990 | Specifications for particular types of winding wires. Part 24: Polyester or polyesterimide enamelled round aluminium wire overcoated with polyamide, class 180 |
EN 60317-47:2014 | Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240 |
IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
IEC 61857-1:2008 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
EN 60317-21:2014 | Specifications for particular types of winding wires - Part 21: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 155 |
EN 60317-13:2010 | Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200 |
EN 61033 : 2006 | TEST METHODS FOR THE DETERMINATION OF BOND STRENGTH OF IMPREGNATING AGENTS TO AN ENAMELLED WIRE SUBSTRATE |
EN 60317-19:1995/A2:2000 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 130 |
IEC 60317-13:2010 | Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200 |
EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
EN 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
IEC 60317-20:2013 | Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155 |
IEC 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
IEC 60317-22:2004+AMD1:2009 CSV | Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 |
EN 60317-20:2014 | Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155 |
IEC 60317-46:2013 | Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240 |
EN 60317-8:2010 | Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180 |
EN 60317-22:2004/A1:2010 | Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 |
IEC 60317-29:1990 | Specifications for particular types of winding wires. Part 29: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular copper wire, class 200 |
IEC 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
EN 60317-23:2014 | Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180 |
EN 60317-24 : 1995 AMD 1 1998 | SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 24: POLYESTER OR POLYESTERIMIDE ENAMELLED ROUND ALUMINIUM WIRE OVERCOATED WITH POLYAMIDE, CLASS 180 |
EN 60505:2011/AC:2017-03 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS (IEC 60505:2011/COR1:2017) |
HD 555.7 : 200S2 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYIMIDE ENAMELLED ROUND COPPER WINDING WIRE, CLASS 220 |
EN 60317-42:1997/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200 |
IEC 61033:1991 | Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate |
EN 60317-51:2014 | Specifications for particular types of winding wires - Part 51: Solderable polyurethane enamelled round copper wire, class 180 |
EN 61857-1:2009 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
EN 60317-4:1994/A2:2000 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130 |
IEC 60317-16:1990 | Specifications for particular types of winding wires. Part 16: Polyester enamelled rectangular copper wire, class 155 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.