BS EN 61757-1-1:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fibre optic sensors Strain measurement. Strain sensors based on fibre Bragg gratings
Hardcopy , PDF
05-28-2020
English
02-28-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Structure and characteristics
6 Features and characteristics to be reported
7 Features and characteristics to be measured
8 Recommendations for use of FBG measuring
instruments
Annex A (informative) - Further properties of FBG
strain sensors
Annex B (informative) - Blank detail specification
Annex C (informative) - Polarization effects
Annex D (informative) - Applied FBG strain sensors
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Specifies detail specifications for fibre optic sensors using one or more fibre Bragg gratings (FBG) as the sensitive element for strain measurements.
| Committee |
GEL/86/3
|
| DevelopmentNote |
Supersedes 13/30288119 DC. (03/2017)
|
| DocumentType |
Standard
|
| Pages |
56
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of IEC 61757 defines detail specifications for fibre optic sensors using one or more fibre Bragg gratings (FBG) as the sensitive element for strain measurements. Generic specifications for fibre optic sensors are defined in IEC 61757-1:2012.
This standard specifies the most important features and characteristics of a fibre optic sensor for strain measurements based on use of an FBG as the sensitive element, and defines the procedures for their determination. Furthermore, it specifies basic performance parameters and characteristics of the corresponding measuring instrument to read out the optical signal from the FBG. This standard refers to the measurement of static and dynamic strain values in a range of frequencies.
A blank detail specification is provided in Annex B.
| Standards | Relationship |
| IEC 61757-1-1:2016 | Identical |
| EN 61757-1-1:2017 | Identical |
| EN 62129-2 : 2011 | CALIBRATION OF WAVELENGTH/OPTICAL FREQUENCY MEASUREMENT INSTRUMENTS - PART 2: MICHELSON INTERFEROMETER SINGLE WAVELENGTH METERS |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| EN 60793-1-30:2011 | Optical fibres - Part 1-30: Measurement methods and test procedures - Fibre proof test |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| IEC 61757-1:2012 | Fibre optic sensors - Part 1: Generic specification |
| IEC 60793-1-33:2017 | Optical fibres - Part 1-33: Measurement methods and test procedures - Stress corrosion susceptibility |
| EN 60874-1:2012 | Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification |
| IEC TS 62129-3:2014 | Calibration of wavelength/optical frequency measurement instruments - Part 3: Optical frequency meters using optical frequency combs |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
| IEC 60874-1:2011 | Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification |
| EN 60793-1-31:2010 | Optical fibres - Part 1-31: Measurement methods and test procedures - Tensile strength |
| IEC TR 62048:2014 | Optical fibres - Reliability - Power law theory |
| EN 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers |
| EN 60793-2:2016 | Optical fibres - Part 2: Product specifications - General |
| ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
| IEC 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers |
| ASTM D 3039/D3039M : 2017 : REDLINE | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| IEC 62129-2:2011 | Calibration of wavelength/optical frequency measurement instruments - Part 2: Michelson interferometer single wavelength meters |
| EN 61757-1 : 2012 | FIBRE OPTIC SENSORS - PART 1: GENERIC SPECIFICATION (IEC 61757-1:2012) |
| IEC 60793-1-31:2010 | Optical fibres - Part 1-31: Measurement methods and test procedures - Tensile strength |
| IEC 60793-1-30:2010 | Optical fibres - Part 1-30: Measurement methods and test procedures - Fibre proof test |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.