BS EN 60317-31:2016
Current
The latest, up-to-date edition.
Specifications for particular types of winding wires Glass fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 180
Hardcopy , PDF
English
02-29-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
23 Pin hole test
30 Packaging
Bibliography
Annex ZA (normative) - Normative references to
international Publications with their
corresponding European publications
Defines the requirements of glass fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper winding wire, temperature index 180.
| Committee |
W/-
|
| DevelopmentNote |
Renumbers and supersedes BS 6811-6.1(1993). 1997 version incorporates amendment 9460 to BS 6811-6.1(1993). (10/2005) Supersedes 03/311118 DC. (09/2007) Supersedes 14/30296568 DC. (02/2016)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of IEC 60317 specifies the requirements of glass fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper winding wire, temperature index 180.
NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temperature cannot be specified.
The range of nominal conductor dimensions covered by this standard is:
| – | width: | min. | 2,0 mm | max. | 16,0 mm; |
| – | thickness: | min. | 0,80 mm | max. | 5,60 mm. |
The specified combinations of width and thickness as well as the specified width/thickness ratio are according to IEC 60317-0-4.
| Standards | Relationship |
| SN EN 60317-31 : 2016 | Identical |
| EN 60317-31:2016 | Identical |
| UNE-EN 60317-31:2016 | Identical |
| NBN EN 60317-31 : 2016 | Identical |
| IEC 60317-31:2015 | Identical |
| DIN EN 60317-31:2016-08 | Identical |
| I.S. EN 60317-31:2016 | Identical |
| EN 62002-2:2008 | Identical |
| IEC 60317-0-4:2015 | Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire |
| EN 60317-0-4:2016 | Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.