BS EN 508-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet Stainless steel
Hardcopy , PDF
11-01-2021
English
03-31-2009
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
3.1 General
3.2 Materials
3.3 Profiles
3.4 Product geometry
3.5 Symbols and abbreviations
4 Requirements
4.1 General
4.2 Materials
4.2.1 Grades
4.2.2 Chemical composition
4.2.3 Physical properties
4.2.4 Surface finishes of stainless steel
4.2.5 Tin coated stainless steel
4.2.6 Organic coated stainless steel
4.3 Products
4.3.1 Mechanical resistance
4.3.2 Calculation and tests of mechanical resistance
4.3.3 Dimensions
4.3.4 Dimensional tolerances for the profiled sheets
4.3.5 Safety in case of fire
5 Test methods
5.1 Material properties
5.2 Structural properties
6 Designation
7 Marking, labelling and packaging
7.1 Marking and labelling
7.2 Packaging and special ordering conditions
7.3 Transport, storage and handling
Annex A (informative) - Physical properties
Annex B (normative) - Dimensional tolerances
B.1 Tolerances for trapezoidal sheets
B.1.1 General
B.1.2 Depth of profile
B.1.3 Depth of stiffeners
B.1.4 Pitch
B.1.5 Widths of crown and valley
B.1.6 Cover width
B.1.7 Radius of bends
B.1.8 Deviation from straightness
B.1.9 Deviation from squareness
B.1.10 Length
B.1.11 Deviation of side lap
B.1.12 Curve radius and angles
B.2 Tolerances for sinusoidal profiles
B.3 Tolerances on tiles
B.3.1 General
B.3.2 Depth of tile
B.3.3 Web angular displacement
B.3.4 Pitch
B.3.5 Width of crown and valley
B.3.6 Cover width
B.3.7 Radius of bends
B.3.8 Deviation from straightness
B.3.9 Deviation from squareness
B.3.10 Length
B.3.11 Contraction or bulging
B.4 Methods for measuring profiles
B.4.1 General
B.4.2 Depth of profile
B.4.3 Depth of stiffeners
B.4.4 Pitch
B.4.5 Width of crown and valley
B.4.6 Cover width
B.4.7 Radius of bends
B.4.8 Straightness
B.4.9 Squareness
B.4.10 Length
B.4.11 Side laps
B.4.12 Side lap ripple
Annex C (informative) - Test methods for concentrated load
Bibliography
Describes requirements for self-supporting roofing products for discontinuous laying made from stainless steel sheet with or without additional metallic and/or organic coatings.
| Committee |
B/542/5
|
| DevelopmentNote |
Supersedes 96/104026 DC. (09/2002) Supersedes 07/30168410 DC. (03/2009)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 508-3 : 2008 | Identical |
| UNI EN 508-3 : 2008 | Identical |
| I.S. EN 508-3:2008 | Identical |
| NS EN 508-3 : 2ED 2008 | Identical |
| SN EN 508-3 : 2008 | Identical |
| NEN EN 508-3 : 2008 | Identical |
| UNE-EN 508-3:2010 | Identical |
| EN 508-3:2008 | Identical |
| DIN EN 508-3:2009-07 | Identical |
| NF EN 508-3 : 2008 | Identical |
| ONORM EN 508-3 : 2009 | Identical |
| BS 5427(2016) : 2016 | CODE OF PRACTICE FOR THE USE OF PROFILED SHEET FOR ROOF AND WALL CLADDING ON BUILDINGS |
| 15/30095322 DC : 0 | BS 5427 - CODE OF PRACTICE FOR THE USE OF PROFILED SHEET FOR ROOF AND WALL CLADDING ON BUILDINGS |
| ISO 9445:2002 | Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths Tolerances on dimensions and form |
| EN 10169-2:2006 | Continuously organic coated (coil coated) steel flat products - Part 2: Products for building exterior applications |
| EN 10169-3:2003 | Continuously organic coated (coil coated) steel flat products - Part 3: Products for building interior applications |
| EN 10169-1:2003 | Continuously organic coated (coil coated) steel flat products - Part 1: General information (definitions, materials, tolerances, test methods) |
| EN 14782:2006 | Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements |
| DIN 18807-2 : 1987 AMD 1 2001 | TRAPEZOIDAL SHEETING IN BUILDING - STEEL TRAPEZOIDAL SHEETING - EXECUTION AND EVALUATION OF ULTIMATE STRENGTH TESTS |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| ISO 7438:2016 | Metallic materials Bend test |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| NFP 34 503 : 1995 | PROFILED SHEETING MADE OF COATED OR NON-COATED STEEL SHEET AND PANELS - BENDING TESTS UNDER LINEAR LOADS AND/OR UNDER CONCENTRATED LOADS |
| EN ISO 9445:2006 | Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002) |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.