BS EN 4595:2013
Current
The latest, up-to-date edition.
Aerospace series. Paints and varnishes. Two component cold curing polyurethane finish. Subsonic erosion resistance
Hardcopy , PDF
English
01-31-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Batch release and qualification testing
6 Designation
Describes the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem e.g. leading edges and air intakes.
| Committee |
ACE/65
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This standard specifies the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem e.g. leading edges and air intakes. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.
| Standards | Relationship |
| EN 4595:2013 | Identical |
| EN 23270:1991 | Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing (ISO 3270:1984) |
| EN 2334:1997 | Aerospace series - Chromic-sulphuric acid pickle of aluminium and aluminium alloys |
| PREN 2379 : 200P1 | AEROSPACE SERIES - FLUIDS FOR ASSESSMENT OF NON-METALLIC MATERIALS |
| EN ISO 2431:2011 | Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011) |
| ISO 3675:1998 | Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method |
| ISO 2884-1:1999 | Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear |
| EN ISO 3675:1998 | Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO 3675:1998) |
| EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
| EN ISO 9514:2005 | Paints and varnishes - Determination of the pot life of multicomponent coating systems - Preparation and conditioning of samples and guidelines for testing (ISO 9514:2005) |
| ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
| EN ISO 2884-1:2006 | Paints and varnishes - Determination of viscosity using rotary viscometers - Part 1: Cone-and-plate viscometer operated at a high rate of shear (ISO 2884-1:1999) |
| EN ISO 1513:2010 | Paints and varnishes - Examination and preparation of test samples (ISO 1513:2010) |
| ISO 11890-1:2007 | Paints and varnishes — Determination of volatile organic compound (VOC) content — Part 1: Difference method |
| EN ISO 3680:2004 | Determination of flash/no flash - Rapid equilibrium closed cup method (ISO 3680:2004) |
| EN ISO 9117-1:2009 | Paints and varnishes - Drying tests - Part 1: Determination of through-dry state and through-dry time (ISO 9117-1:2009) |
| PREN 3837 : 200P1 | AEROSPACE SERIES - PAINTS AND VARNISHES - NATURE AND METHOD FOR SURFACE PREPARATION OF TEST PIECES IN ALUMINIUM ALLOYS |
| EN ISO 11890-1:2007 | Paints and varnishes - Determination of volatile organic compound (VOC) content - Part 1: Difference method (ISO 11890-1:2007) |
| ISO 2812:1974 | Paints and varnishes — Determination of resistance to liquids |
| ISO 1513:2010 | Paints and varnishes Examination and preparation of test samples |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| ISO 3680:2004 | Determination of flash/no flash Rapid equilibrium closed cup method |
| ISO 3270:1984 | Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN ISO 3679:2015 | Determination of flash no-flash and flash point - Rapid equilibrium closed cup method (ISO 3679:2015) |
| ISO 9117-1:2009 | Paints and varnishes — Drying tests — Part 1: Determination of through-dry state and through-dry time |
| ISO 9514:2005 | Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing |
| EN 3840:2007 | Aerospace series - Paints and varnishes - Technical specification |
| ISO 2813:2014 | Paints and varnishes — Determination of gloss value at 20°, 60° and 85° |
| EN ISO 2813:2014 | Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014) |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
| ISO 2431:2011 | Paints and varnishes Determination of flow time by use of flow cups |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.