BS EN 40-5:2002
Current
The latest, up-to-date edition.
Lighting columns Requirements for steel lighting columns
Hardcopy , PDF
English
07-17-2002
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Definitions
4 Materials
5 Dimensions
6 Design and design verification
7 Welding
8 Joints
9 Impact resistance
10 Internal finish and sharp edges
11 Corrosion protection
12 Marking
13 Conformity control
14 Acceptance criteria
15 Re-testing
Annex A (informative) Corrosion protection measures for
steel lighting columns
Annex B (informative) Recommendations for storage and
installation
Annex C (informative) Bibliography
Defines requirements for steel lighting columns. Includes materials and conformity control. Applies to post top columns and columns with brackets not exceeding 18 m in height for side entry lanterns.
| Committee |
B/509/50
|
| DevelopmentNote |
Together with BS EN 40-6, supersedes BS 5649-3(1982) and BS 5649-4(1982) (07/2000) Supersedes 95/104350 DC. (03/2006)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This European Standard specifies requirements for steel lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.
This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards.
It provides for the evaluation of conformity of the products to this European Standard.
| Standards | Relationship |
| EN 40-5:2002 | Identical |
| NF EN 40-5 : 2002 | Identical |
| NS EN 40-5 : 2ED 2002 | Identical |
| UNE-EN 40-5:2003 | Identical |
| UNI EN 40-5 : 2003 | Identical |
| NEN EN 40-5 : 2002 | Identical |
| I.S. EN 40-5:2002 | Identical |
| NBN EN 40-5 : 2002 | Identical |
| SN EN 40-5 : 2002 | Identical |
| DIN EN 40-5:2002-09 | Identical |
| BS PAS 68(2007) : 2007 | SPECIFICATION FOR VEHICLE SECURITY BARRIERS |
| BS PAS 68(2010) : 2010 | IMPACT TEST SPECIFICATIONS FOR VEHICLE SECURITY BARRIERS |
| BS PAS 68(2005) : 2005 | SPECIFICATION FOR VEHICLE SECURITY BARRIERS - FIXED BOLLARDS |
| ISO 2063:2005 | Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys |
| EN 40-3-1:2013 | Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
| EN 288-1:1992/A1:1997 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES FOR FUSION WELDING |
| EN 288-3:1992/A1:1997 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 3: WELDING PROCEDURE TESTS FOR THE ARC WELDING OF STEELS |
| EN 40-3-2:2013 | Lighting columns - Part 3-2: Design and verification - Verification by testing |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| EN 50102:1995/corrigendum Jul. 2002 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES FOR ELECTRICAL EQUIPMENT AGAINST EXTERNAL MECHANICAL IMPACTS (IK CODE) |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| ISO 1463:2003 | Metallic and oxide coatings Measurement of coating thickness Microscopical method |
| ISO 9717:2017 | Metallic and other inorganic coatings — Phosphate conversion coating of metals |
| EN 288-2:1992/A1:1997 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 2: WELDING PROCEDURE SPECIFICATION FOR ARC WELDING |
| EN 40-1:1991 | Lighting columns - Part 1: Definitions and terms |
| EN 12767:2007 | Passive safety of support structures for road equipment - Requirements, classification and test methods |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 288-8 : 1995 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 8: APPROVAL BY A PRE-PRODUCTION WELDING TEST |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| PREN 40-3-3 : DRAFT 2012 | LIGHTING COLUMNS - PART 3-3: DESIGN AND VERIFICATION - VERIFICATION BY CALCULATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.