BS EN 1889-1:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Machines for underground mines. Mobile machines working underground. Safety Rubber tyred vehicles
Hardcopy , PDF
03-07-2019
English
08-31-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or safety measures
6 Verification of safety requirements
7 Information for use
Annex A (normative) - Brake testing
Annex B (normative) - Verification data for safety requirements
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes the safety requirements and tests for self-propelled rubber tyred vehicles as defined in 3.1 intended primarily for use in underground mining (i.e. as mine vehicles) and other underground workings (e.g. as tunnelling vehicles).
| Committee |
MRE/1
|
| DevelopmentNote |
Supersedes 95/706094 DC (08/2003) Supersedes 10/30185766 DC. (08/2011)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This European Standard specifies the safety requirements and tests for self-propelled rubber tyred vehicles as defined in 3.1 intended primarily for use in underground mining (i.e. as mine vehicles) and other underground workings (e.g. as tunnelling vehicles). The electrical supply voltage is limited to 1100 A.C. and 1500 D.C.
1.2 This European Standard deals with all significant hazards, hazardous situations and hazardous events, applying to self-propelled, rubber-tyred vehicles, subject to being used according to their intended purpose and prevailing manufacturer’s conditions and within the scope of foreseeable misuse. This European Standard describes appropriate action to be taken to avoid or minimize the risk of significant hazards.
1.3 This European Standard does not include rubber tyred drilling rigs, which are covered by EN 791, or earth-moving machinery not intended primarily for use in underground mines, which are covered by EN 474 (all parts). This European Standard does not take account of specific hazards associated with special-purpose vehicles, e.g. tankers, explosives vehicles.
This standard does not cover the use and operation of rubber-tyred vehicles being remotely controlled or operation in potentially explosive atmospheres.
1.4 This European Standard applies to vehicles which are manufactured after the date of issue of this standard.
| Standards | Relationship |
| NEN EN 1889-1 : 2011 | Identical |
| EN 1889-1:2011 | Identical |
| SN EN 1889-1 : 2011 | Identical |
| UNI EN 1889-1 : 2011 | Identical |
| NF EN 1889-1 : 2011 | Identical |
| DIN EN 1889-1:2011-10 | Identical |
| NBN EN 1889-1 : 2011 | Identical |
| I.S. EN 1889-1:2011 | Identical |
| NS EN 1889-1 : 2011 | Identical |
| UNE-EN 1889-1:2012 | Identical |
| BS 6164:2011 | Code of practice for health and safety in tunnelling in the construction industry |
| 11/30218915 DC : DRAFT JAN 2011 | BS 6164 - CODE OF PRACTICE FOR HEALTH AND SAFETY IN TUNNELING IN THE CONSTRUCTION INDUSTRY |
| ISO 3449:2005 | Earth-moving machinery — Falling-object protective structures — Laboratory tests and performance requirements |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| EN ISO 2860:2008 | Earth-moving machinery - Minimum access dimensions (ISO 2860:1992) |
| ISO 8030:2014 | Rubber and plastics hoses — Method of test for flammability |
| EN 60825-4:2006/A2:2011 | SAFETY OF LASER PRODUCTS - PART 4: LASER GUARDS |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| EN ISO 6683:2008 | Earth-moving machinery - Seat belts and seat belt anchorages - Performance requirements and tests (ISO 6683:2005) |
| ISO 10570:2004 | Earth-moving machinery — Articulated frame lock — Performance requirements |
| ISO 13333:1994 | Earth-moving machinery Dumper body support and operator's cab tilt support devices |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 7096:2000 | Earth-moving machinery Laboratory evaluation of operator seat vibration |
| ISO 3411:2007 | Earth-moving machinery Physical dimensions of operators and minimum operator space envelope |
| ISO 6683:2005 | Earth-moving machinery Seat belts and seat belt anchorages Performance requirements and tests |
| EN ISO 3449:2008 | Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements (ISO 3449:2005) |
| EN ISO 3411:2007 | Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007) |
| ISO 6405-2:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 2: Symbols for specific machines, equipment and accessories |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| ISO 12508:1994 | Earth-moving machinery Operator station and maintenance areas Bluntness of edges |
| EN 1679-1:1998+A1:2011 | Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60825-4:2006+AMD1:2008+AMD2:2011 CSV | Safety of laser products - Part 4: Laser guards |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| IEC 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| ISO 5010:2007 | Earth-moving machinery Rubber-tyred machines Steering requirements |
| ISO 6396:2008 | Earth-moving machinery Determination of emission sound pressure level at operator's position Dynamic test conditions |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 12509:2004 | Earth-moving machinery — Lighting, signalling and marking lights, and reflex-reflector devices |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 60332-1-2:2004/A11:2016 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| IEC 60332-1-1:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulatedwire or cable - Apparatus |
| ISO 6393:2008 | Earth-moving machinery Determination of sound power level Stationary test conditions |
| EN 791:1995+A1:2009 | Drill rigs - Safety |
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| ISO 9244:2008 | Earth-moving machinery Machine safety labels General principles |
| EN ISO 3450:2011 | Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems (ISO 3450:2011) |
| ISO 3471:2008 | Earth-moving machinery — Roll-over protective structures — Laboratory tests and performance requirements |
| EN ISO 8030:2014 | Rubber and plastics hoses - Method of test for flammability (ISO 8030:2014) |
| ISO 1813:2014 | Belt drives — V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts — Electrical conductivity of antistatic belts: Characteristics and methods of test |
| EN 60332-1-1:2004/A1:2015 | Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus |
| ISO 2860:1992 | Earth-moving machinery — Minimum access dimensions |
| ISO 5006:2017 | Earth-moving machinery — Operator's field of view — Test method and performance criteria |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
| ISO 6405-1:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 1: Common symbols |
| EN ISO 3471:2008 | Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements (ISO 3471:2008) |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 6682:2008 | Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989) |
| IEC 60332-2-1:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 6395:2008 | Earth-moving machinery Determination of sound power level Dynamic test conditions |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN 60332-2-1:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus |
| EN ISO 2867:2011 | Earth-moving machinery - Access systems (ISO 2867:2011) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 10533:1993 | Earth-moving machinery — Lift-arm support devices |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 2867:2011 | Earth-moving machinery Access systems |
| ISO 9533:2010 | Earth-moving machinery Machine-mounted audible travel alarms and forward horns Test methods and performance criteria |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| ISO 3450:2011 | Earth-moving machinery — Wheeled or high-speed rubber-tracked machines — Performance requirements and test procedures for brake systems |
| ISO 6805:1994 | Rubber hoses and hose assemblies for underground mining Wire-reinforced hydraulic types for coal mining Specification |
| ISO 7745:2010 | Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use |
| ISO 3864-4:2011 | Graphical symbols Safety colours and safety signs Part 4: Colorimetric and photometric properties of safety sign materials |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.