BS EN 14035-15:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fireworks Fountains. Specification and test methods
Hardcopy , PDF
10-31-2010
BS EN 15947-4 : 2016
BS EN 15947-5:2010
BS EN 15947-3:2015
BS EN 15947-3:2010
BS EN 15947-4:2010
English
03-14-2006
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Construction
4.1 Means of ignition
4.2 Attachment of initial fuse (outdoor fountains only)
4.3 Protection of initial fuse
4.4 Materials of firework case
4.5 Integrity
4.6 Net explosive content
4.7 Vertical stability
5 Performance
5.1 Indoor fountains
5.2 Initial fuses (outdoor fountains only)
5.3 Principle effects
5.4 Functioning
5.5 Explosions and other failures
5.6 Height of effects and burning matter (indoor fountains
only)
5.7 Burning matter (outdoor fountains only)
5.8 Stability
6 Primary pack or selection pack
7 Minimum labelling requirements
7.1 General
7.2 Type name and category
7.3 Safety information
7.4 Name, address and telephone number of manufacturer or
distributor or importer
7.5 Reference to this standard
7.6 Printing
7.7 Marking of very small fountains
7.8 Additional information on the primary pack (if applicable)
8 Test methods
8.1 Attachment of protruding fuse (type test and
batch test)
8.2 Attachment of sealing paper and ignition
head (type test)
8.3 Vertical stability test (type test)
8.4 Performance of indoor fountains (type test and
batch test)
8.5 Performance of outdoor fountains (type test and
batch test)
8.6 Determination of net explosive content (type test)
8.7 Side ignition of initial fuse (type test)
8.8 Labelling (type test and batch test)
Annex A (normative) Type testing
Annex B (normative) Batch testing
Annex C (normative) Specification for test paper
Annex D (normative) Method for determination of smouldering
rate of cigarette
Annex E (informative) A-Deviations
Gives requirements for the construction, performance, primary packaging and labelling of fountains and the corresponding test methods. Applies to indoor fireworks which are classified as fountains in category 1 in EN 14035-2 and in which the pyrotechnic composition is based on nitrocellulose with a mass fraction of nitrogen of not more than 12,6%.
Committee |
CII/47
|
DevelopmentNote |
Partially supersedes BS 7114-2(1988) and BS 7114-3(1988) Supersedes 00/123942 DC. (08/2003) Inactive for the new design. (11/2010)
|
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NBN EN 14035-15 : 2003 | Identical |
UNI EN 14035-15 : 2005 | Identical |
NF EN 14035-15 : 2003 | Identical |
SN EN 14035-15 : 2003 CORR 2005 | Identical |
NS EN 14035-15 : 1ED 2003 | Identical |
I.S. EN 14035-15:2003 | Identical |
NEN EN 14035-15 : 2003 C1 2005 | Identical |
UNE-EN 14035-15:2004 | Identical |
DIN EN 14035-15:2003-09 | Identical |
05/19983621 DC : DRAFT MAY 2005 | BS 14035 - FIREWORKS - SELECTION PACKS - SPECIFICATION |
BS DD14035(2007) : 2007 | FIREWORKS - SELECTION PACKS - SPECIFICATION |
ISO 845:2006 | Cellular plastics and rubbers — Determination of apparent density |
ISO 187:1990 | Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples |
EN ISO 845:2009 | Cellular plastics and rubbers - Determination of apparent density (ISO 845:2006) |
EN ISO 536:2012 | Paper and board - Determination of grammage (ISO 536:2012) |
EN 20187:1993 | Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples (ISO 187:1990) |
ISO 536:2012 | Paper and board Determination of grammage |
ISO 2439:2008 | Flexible cellular polymeric materials Determination of hardness (indentation technique) |
EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
EN ISO 2439:2008 | Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:2008) |
ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.