BS EN 13480-2:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Metallic industrial piping Materials
Hardcopy , PDF
02-05-2020
English
09-21-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
1 Scope
2 Normative references
3 Terms and definitions, symbols and units
4 Requirements for materials to be used for
pressure containing parts in industrial piping
5 Requirements for materials to be used for
non-pressure parts
Annex A (normative) - Grouping system for
steels for pressure equipment
Annex B (normative) - Requirements for
prevention of brittle fracture at low
temperatures
Annex C (normative) - Provisional technical
delivery conditions for clad products for
pressure purposes
Annex D (informative) - European steels for
pressure purposes
Annex Y (informative) - History of EN 13480-2
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2014/68/EU
aimed to be covered
Bibliography
Defines the requirements for materials (including metallic clad materials) for industrial piping and supports covered by EN 13480-1 manufactured from of metallic materials.
| Committee |
PVE/10
|
| DevelopmentNote |
Together with BS EN 13480-1, BS EN 13480-3, BS EN 13480-4 and BS EN 13480-5, supersedes BS 806(1993) Supersedes 99/707159 DC (07/2002) Supersedes 09/30188143 DC and 09/30122688 DC. (06/2011) Supersedes 15/30324151 DC. (10/2016)
|
| DocumentType |
Standard
|
| Pages |
88
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This Part of this European Standard specifies the requirements for materials (including metallic clad materials) for industrial piping and supports covered by EN13480-1 manufactured from of metallic materials. It is currently limited to steels with sufficient ductility. This Part of this European Standard is not applicable to materials in the creep range. NOTE Other materials will be added later by amendments. It specifies the requirements for the selection, inspection, testing and marking of metallic materials for the fabrication of industrial piping.
| Standards | Relationship |
| EN 13480-2:2017 | Identical |
| UNI EN 13480-2 : 2013 | Identical |
| NS EN 13480-2 : 2017 | Identical |
| I.S. EN 13480-2:2017 | Identical |
| DIN EN 13480-2:2014-12 | Identical |
| NBN EN 13480-2 : 2012 AMD 2 2016 | Identical |
| NEN EN 13480-2 : 2017 | Identical |
| ONORM EN 13480-2 : 2017 | Identical |
| NF EN 13480-2 : 2017 | Identical |
| UNE-EN 13480-2:2017 | Identical |
| DEFSTAN 02-348/2(2008) : 2008 | GUIDE TO THE DESIGN, CORROSION ASSESSMENT AND STRESS ANALYSIS OF STEAM SYSTEMS PIPEWORK |
| 12/30258581 DC : 0 | BS 5908-2 - FIRE AND EXPLOSION PRECAUTIONS AT PREMISES HANDLING FLAMMABLE GASES, LIQUIDS AND DUSTS - PART 2: GUIDE TO APPLICABLE STANDARDS AND REGULATIONS |
| BS 10:2009 | Specification for flanges and bolting for pipes, valves and fittings |
| BS 5908-2:2012 | Fire and explosion precautions at premises handling flammable gases, liquids and dusts Guide to applicable standards and regulations |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| ISO 14343:2017 | Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels — Classification |
| EN 10079:2007 | Definition of steel products |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN 13480-4:2017 | Metallic industrial piping - Part 4: Fabrication and installation |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 10028-6:2017 | Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered |
| ISO/TR 15608:2017 | Welding — Guidelines for a metallic materials grouping system |
| EN 13480-1:2017 | Metallic industrial piping - Part 1: General |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| EN 10028-5:2017 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled |
| EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN ISO 14343:2017 | Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017) |
| EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| CEN ISO/TR 15608:2017 | Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 12074:2000 | Welding consumables - Quality requirements for manufacture, supply and distribution of consumables for welding and allied processes |
| AD MERKBLATT W8 : 2001 | MATERIALS - CLAD STEELS |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| EN 13480-5:2017 | Metallic industrial piping - Part 5: Inspection and testing |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| SEL 075 : 1983 | PLATED PRODUCTS |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| EN 13479:2017 | Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials |
| EN 10216-3:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.