BS EN 12953-3:2016
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Shell boilers Design and calculation for pressure parts
Hardcopy , PDF
07-09-2024
English
07-09-2024
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 General
6 Calculation temperature and nominal design
stress
7 Cylindrical shells
8 Openings and branches in cylindrical shells
9 Ends
10 Supported flat plates, stays and
stiffeners
11 Design of isolated openings in boiler flat end
plates
12 Unpierced tubes and tube plates
13 Furnaces tubes, furnace components and
reversal chambers of cylindrical form subject
to external pressure
14 Access and inspection openings
Annex A (informative) - Calculation form for
'Walker' -type reverse curve sections or
corrugations
Annex B (normative) - Furnace calculation
temperature
Annex D (normative) - Economizer and superheater
with water tube design connected to the shell boiler
Annex E (informative) - Significant technical changes
between this European Standard and the previous
edition
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 2014/68/EU
aimed to be covered
Bibliography
Defines requirements for the design and calculation of pressure parts of shell boilers as defined in EN 12953-1.
| Committee |
PVE/2
|
| DevelopmentNote |
Partially supersedes BS 2790(1992) Supersedes 98/711457 DC (07/2002) Supersedes 13/30288560 DC. (05/2016)
|
| DocumentType |
Standard
|
| ISBN |
9780580840258
|
| Pages |
114
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| Supersedes |
This Part of this European Standard specifies requirements for the design and calculation of pressure parts of shell boilers as defined in EN 12953 1. NOTE For other components such as economisers, superheaters, tube walls, headers, reference should be made to EN 12952 series.
| Standards | Relationship |
| DIN EN 12953-3:2002-08 | Identical |
| UNE-EN 12953-3:2017 | Identical |
| I.S. EN 12953-3:2016 | Identical |
| DIN EN 12953-3:2013-10 (Draft) | Identical |
| NBN EN 12953-3 : 2016 | Identical |
| NF EN 12953-3 : 2016 | Identical |
| SN EN 12953-3 : 2016 | Identical |
| NEN EN 12953-3 : 2016 | Identical |
| NS EN 12953-3 : 2002 | Identical |
| UNI EN 12953-3 : 2005 | Identical |
| EN 12953-3:2016 | Identical |
| EN 12953-3:2016/AC:2024 | Identical |
| EEMUA 193 : 2013 | MANAGING COMPETENCE ASSURANCE FOR PERSONNEL UNDERTAKING IN-SERVICE INSPECTION OF PRESSURE EQUIPMENT |
| EN 12953-5:2002 | Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler |
| EN 14394:2005+A1:2008 | Heating boilers - Heating boilers with forced draught burners - Nominal heat output not exceeding 10 MW and maximum operating temperature of 110 °C |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| EN 13445-6 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| EN 12953-6:2011 | Shell Boilers - Part 6: Requirements for equipment for the boiler |
| CR 13445-7:2002 | Unfired pressure vessels - Part 7: Guidance on the use of the conformity procedures |
| EN 12952-3:2011 | Water-tube boilers and auxiliary installations - Part 3: Design and calculation for pressure parts of the boiler |
| CEN/TR 764-6:2012 | Pressure equipment - Part 6: Structure and content of operating instructions |
| EN 12953-1:2012 | Shell boilers - Part 1: General |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| EN 12953-2:2012 | Shell boilers - Part 2: Materials for pressure parts of boilers and accessories |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| EN 12953-10:2003 | Shell boilers - Part 10 : Requirements for feedwater and boiler water quality |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.