BS EN 1218-5 : 2004
Current
Current
The latest, up-to-date edition.
SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
Amended by
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2004
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (informative) - Examples of safety related
electronic control systems
Annex B (normative) - Tool spindle dimensional tolerances
Annex C (normative) - Operating conditions for noise
emission measurement
Annex ZA (informative) - Relationship between this
European Standard and the
Essential Requirements of
EU Directive 98/37/EC
Annex ZB (informative) - Relationship between this
European Standard and the
Essential Requirements of
EU Directive 2006/42/EC
Bibliography
Describes all significant hazards, hazardous situations and events, which are relevant to one side profiling machines with fixed table and feed rollers or feed chain hereinafter referred to as "machines", where the loading and unloading is manual and where the maximum work-piece height capacity is 200 mm.
| Committee |
MTE/23
|
| DevelopmentNote |
Supersedes 98/705594 DC (07/2004) 2004 Edition Re-Issued in November 2009 & incorporates AMD 1 2009. Supersedes 09/30178385 DC. (11/2009)
|
| DocumentType |
Standard
|
| Pages |
60
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ONORM EN 1218-5 : 2010 | Identical |
| UNI EN 1218-5 : 2010 | Identical |
| NEN EN 1218-5 : 2004 + A1 2009 | Identical |
| SN EN 1218-5 : 2004 + A1 2010 | Identical |
| I.S. EN 1218-5:2004 | Identical |
| NF EN 1218-5 : 2004 + A1 2010 | Identical |
| EN 1218-5:2004+A1:2009 | Identical |
| UNE-EN 1218-5:2005 | Identical |
| NBN EN 1218-5 : 2004 + A1 2009 | Identical |
| DIN EN 1218-5:2010-02 | Identical |
| NS EN 1218-5 : 2004 + A1 2009 | Identical |
| EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| EN 50370-2:2003 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| EN 12779:2015 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN 1218-1:1999+A1:2009 | Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table |
| HD 22-1 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS |
| HD 21.1 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 354:2003 | Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 1218-3:2001+A1:2009 | Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| EN 847-1:2017 | Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| EN 50370-1:2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| EN 1218-2:2004+A1:2009 | Safety of woodworking machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.