BS CP312-3(1973) : 1973
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CODE OF PRACTICE FOR PLASTICS PIPEWORK (THERMOPLASTICS MATERIAL) - POLYETHYLENE PIPES FOR THE CONVEYANCE OF LIQUIDS UNDER PRESSURE
12-10-2010
11-23-2012
Foreword
1. General
1.1 Scope
1.2 Classification of polyethylenes
2. Working pressure and effects of temperature
3. Limitations
4. Flow properties
5. Jointing procedures
5.1 General
5.2 Metal fittings
5.3 Plastics fittings
5.4 Thermofusion welding
6. Bending
6.1 Cold bending
6.2 Hot bending
7. Storage, handling and transport
7.1 Storage
7.2 Handling
7.3 Transport
8. Inspection
9. Installation
9.1 General
9.2 Installation of buried pipes
9.3 Above ground installations
9.4 Support spacings
9.5 Expansion and contraction
10. Test pressures and testing
10.1 Hydrostatic test pressures
10.2 Hydrostatic testing
11. Repairs
Tables
1. Reduction in working pressures for polyethylene
pipes at elevated temperatures
2. Recommended spacing of support centres for
horizontal polyethylene pipes
Figure
1. Heated tool for fusion welding
Provides guidance on the proper application and installation of polyethylene pipe for the conveyance of liquids under pressure. The choice of materials or particular applications is covered. Does not recommend the use of polyethylene pipe for any particular purpose. The use of plastics pipes in services supplied from the mains of water undertakings is governed by the byelaws of the undertakings and these shall be strictly observed. Not recommended for use in ground that is, or might be, liable to severe gas contamination. Covers working pressure and effects of temperature, limitations, flow properties, jointing procedures, bending, storage, handling and transport and inspection.
| Committee |
PRI/88
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| 05/30113497 DC : DRAFT APR 2005 | BS 5391-1 - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) FITTINGS FOR USE WITH ABS PRESSURE PIPE - PART 1: SPECIFICATION FOR FITTINGS FOR USE WITH PIPE FOR INDUSTRIAL USES |
| BS 6572:1985 | Specification for blue polyethylene pipes up to nominal size 63 for below ground use for potable water |
| BS 7281:1990 | Specification for polyethylene pipes for the supply of gaseous fuels |
| BS 4346-3:1982 | Joints and fittings for use with unplasticized PVC pressure pipes Specification for solvent cement |
| BS 6700(2006) : 2006 | DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - SPECIFICATION |
| BS 3867:1987 | Method of specifying outside diameters and pressure ratings for pipe of thermoplastics materials (inch series) |
| BS 6700:1997 | Specification for design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages |
| BS 6880-2:1988 | Code of practice for low temperature hot water heating systems of output greater than 45 kW Selection of equipment |
| BS 5955-6:1980 | Plastics pipework (thermoplastics materials) Code of practice for the installation of unplasticized PVC pipework for gravity drains and sewers |
| BS 6700:1987 | Specification for design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages |
| BS 3351:1971 | Specification for piping systems for petroleum refineries and petrochemical plants |
| BS 6785:1986 | Code of practice for solar heating systems for swimming pools |
| BS 7336:1990 | Specification for polyethylene fusion fittings with integral heating element(s) for use with polyethylene pipes for the conveyance of gaseous fuels |
| BS 6730:1986 | Specification for black polyethylene pipes up to nominal size 63 for above ground use for cold potable water |
| BS CP312-1(1973) : 1973 | CODE OF PRACTICE FOR PLASTICS PIPEWORK (THERMOPLASTICS MATERIAL) - GENERAL PRINCIPLES AND CHOICE OF MATERIAL |
| BS 3284:1967 | Specification for polythene pipe (Type 50) for cold water services |
| BS CP99(1972) : LATEST | FROST PRECAUTIONS FOR WATER SERVICES |
| BS 3796(1970) : LATEST | POLYTHENE PIPE (TYPE 50) FOR GENERAL PURPOSES INCLUDING CHEMICAL AND FOOD INDUSTRY USES |
| BS 864-3:1975 | Capillary and compression tube fittings of copper and copper alloy Compression fittings for polyethylene pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.