BS 6000:1996
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots
Hardcopy , PDF
07-25-2005
English
05-15-1996
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Committees responsible
National foreword
Introduction
Guide
1 Scope
2 References
3 The selection process
4 Acceptance sampling systems, schemes and plans
5 ISO Standards for 'acceptance' sampling of lots
6 Some general considerations influencing a
selection
7 Making a comparison of the methods for sampling
inspection
8 Other methods sometimes adopted in practice
9 Market and production conditions - effect on the
selection process
10 The final selection - realism
Annexes
A Bibliography
Figures
1 Operating characteristic curve defined by producer's
risk (PR) and consumer's risk (CR)
2 Operating characteristic curve defined by acceptable
quality level (AQL) and limiting quality (LQ)
3 OC curves: Four sampling plans for AQL 1,5%
non-conforming, normal inspection, single sampling
4 Normal distribution
5 Distribution with large positive skewness
6 Comparison of operating characteristic curves for
single, double, multiple and sequential sampling
plans (code letter L, AQL 0,65%
7 Comparison of average sample sizes for single,
double, multiple and sequential sampling
(for acceptance plans of figure 6)
8 Chart illustrating the selection procedures when
production is continuous and run length exceeds 10
lots of original inspection
9 Chart illustrating the selection procedures when
production is not continuous or run is 10 lots or
fewer
Tables
1 Comparison of sample sizes in inspection by
attributes and by variables
2 Equivalent sampling plans for code letter L,
AQL 0,65
3 Guide for selection of a candidate acceptance
sampling system, scheme or plan based on the
inspection situation
4A Guide for the selection of an acceptance sampling
system, scheme or plan, using existing market
conditions
4B Guide for the selection of an acceptance sampling
system, scheme or plan, using existing production
conditions
Gives advice in the selection of an acceptance sampling system, scheme or plan. Applies to a wide variety of inspection situations. Deals only with confined acceptance sampling of products that are supplied in lots and that can be classified as consisting of products that are supplied in lots and that can be classified as consisting of discrete items (discrete articles of product).
| Committee |
SS/5
|
| DevelopmentNote |
Together with BS 6001-0(1996), supersedes BS 6000(1972). Also numbered as ISO TR 8550. (06/2004)
|
| DocumentType |
Standard
|
| Pages |
58
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS 6001-4:1994 | Sampling procedures for inspection by attributes Specification for sequential sampling plans |
| BS ISO 3534-2:2006 | Statistics. Vocabulary and symbols Applied statistics |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| ISO 2854:1976 | Statistical interpretation of data — Techniques of estimation and tests relating to means and variances |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| BS 6001-1(1999) : 1999 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION |
| ISO 8402:1994 | Quality management and quality assurance — Vocabulary |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| BS 2846-4:1976 | Guide to statistical interpretation of data Techniques of estimation and tests relating to means and variances |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| BS ISO 3534-1:2006 | Statistics. Vocabulary and symbols General statistical terms and terms used in probability |
| BS 6002-4.1:1994 | Sampling procedures for inspection by variables. Specification for sequential sampling plans for percent nonconforming. Known standard deviation |
| BS 6001-3:1993 | Sampling procedures for inspection by attributes Specification for skip-lot procedures |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| BS 6001-0:1996 | Sampling procedures for inspection by attributes Introduction to the BS 6001 attribute sampling system |
| ISO 8423:2008 | Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation) |
| BS 6002-1:1993 | Sampling procedures for inspection by variables Specification for single sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection |
| BS EN ISO 8402:1995 | Quality management and quality assurance. Vocabulary |
| ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.