BS 5341-6.5:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabularly, inspection methods and generic specifications. Quality requirements
Hardcopy , PDF
01-30-2006
English
05-01-1992
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Committees responsible
National foreword
Vocabulary
0. Introduction
1. Scope and field of application
2. References
3. Terminology
4. Visible defects
5. Material
6. Raised material caused by marking of rings
7. Machining of periphery and sides - Unintentional
departure from ideal profile and flatness
Tables
1. Permissible values of size, number and spacing of
pores, cavities and sand inclusions
2. Permissible size of indentations and depressions
3. Maximum size of burrs for all sizes of ring
4. Edge material removal in deburr operations
5. Permissible size of chipping and defects on uncoated
rings on peripheral edges, peripheral edges of the
gap and outside gap corners
6. Permissible size of chipping and defects on coated
rings with chromium-plated periphery, on peripheral
edges, peripheral edges of the gap and outside
gap corners
7. Permissible size of chipping and defects on spray-
coated rings on peripheral edges, peripheral edges
of the gap and outside gap corners
8. Permissible size of chipping and defects on chamfers
at the peripheral edge and peripheral edge of the gap
9. Permissible size of chipping and defects on inside
gap corners
10. Test conditions to measure tangential force loss
11. Maximum permitted raised material
12. Permissible side face unevenness in the
circumferential direction
13. Permissible wind
Figures
1. Chipping on peripheral edges of the gap
2. Chipping on peripheral edges
3. Chipping on outside gap corners
4. Combination of figures 1 and 3
5. Chipping on oppposite gap corners
6. Chipping on chamfers
Describes those quality aspects which are capable of definition but not normally found on a drawing specification. It covers single-piece piston rings of grey, carbidic, malleable, spheroidal graphite cast iron or steel, multi-piece piston rings consisting of cast iron parts and spring components and single-piece and multi-piece rings of steel, in the form of strip steel components or steel segments with spring expander components. Does not establish acceptable quality levels. Applies to all rings up to and including 200 mm diameter covered by the above classification for both reciprocating internal combustion engines and compressors. Includes visible defects, material, raised material caused by marking of rings and machining of periphery and sides - unintentional departure from ideal profile and flatness.
| Committee |
MCE/14
|
| DevelopmentNote |
Together with BS 5341-6.1(1992), BS 5341-6.2(1992), BS 5341-6.3(1992), BS 5341-6.4(1992), BS 5341-7.1.1(1992), BS 5341-7.2(1992), BS 5341-7.3.1(1992), BS 5341-7.4(1992) and BS 5341-8.1(1992), it supersedes BS 5341-1(1976), BS 5341-2(1977), BS 5341-3(1976) & BS 5341-4(1976). Also numbered as ISO 6621-5. Supersedes 87/72183 DC. (08/2005)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS 5341-7.1.1:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Designs, dimensions and designations for singlepiece rings. Rectangular compression rings Specification for rectangular rings |
| BS 5341-6.2:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Inspection measuring principles |
| BS 5341-8.1:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Designs, dimensions and designations for multi-piece oil control rings. Specification for coil-spring-loaded oil control rings |
| BS 5341-6.4:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications General specifications |
| BS 5341-7.2:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Designs, dimensions and designations for single piece rings. Specification for scraper rings |
| BS 5341-6.3:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Material specifications |
| BS 5341-6.4:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications General specifications |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| BS 5341-6.1:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Vocabulary |
| BS 5341-6.3:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Material specifications |
| BS 6001(1972) : AMD 5054 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - SPECIFICATION FOR SAMPLING PLANS INDEXED BY ACCEPTABLE QUALITY LEVEL (AQL) FOR LOT - BY - LOT INSPECTION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.