BS 4660(1989) : 1989
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATION FOR UNPLASTICIZED POLYVINYL CHLORIDE (PVC-U) PIPES AND PLASTICS FITTINGS OF NOMINAL SIZES 110 AND 160 FOR BELOW GROUND GRAVITY DRAINAGE AND SEWERAGE
Hardcopy , PDF
01-15-2000
English
01-01-1989
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Committees responsible
Specification
1. Scope
2. Definitions
3. Materials
4. Apparatus
5. Dimensions
6. Physical properties
7. Performance requirements
8. Marking
Appendices
A. Method of test for the impact resistance of
polyolefin fittings
B. Method of test for resistance to diametric
distortion at joints
C. Method of test for resistance to angular deflection
D. Method of test for resistance to combined
temperature cycling and external loading
e. Method of test for resistance to elevated
temperature cycling
F. Method of test for water seal
G. Method of test for resistance to surface loading
H. Guidance on quality control testing
Tables
1. Dimensions of pipes
2. Dimensions of pipe sockets and fittings
3. Dimensions of swept fittings
4. Dimensions of long radius bends
5. Grading of surface loading conditions
6. Plate sizes
7. Applicability of requirements and test methods
Figures
1. Pipe lengths
2. Location of dimensions for pipe sockets and fittings
3. Typical groove designs
4. Location of dimensions for swept fittings
5. Typical channel fittings
6. Typical features of equipment for diametric
distortion test
Describes requirements for unplasticized polyvinyl chloride pipe and fittings for the construction of gravity drains and sewers. For pipe and fittings with sizes 110 and 160. Exposed fittings may be made alternatively of olefin plastics. For use with untreated trade waste or prolonged discharges at high temperatures. Covers definitions, materials, appearance, dimensions, physical properties, performance requirements, marking, test for the impact resistance of polyolefin fittings, resistance to diametric distortion at joints, resistance to angular deflection, resistance to combined temperature cycling and external loading, resistance to elevated temperature cycling, for water seal, resistance to surface loading and guidance on quality control testing. Includes several tables of dimensions.
| Committee |
PRM/61
|
| DevelopmentNote |
BS DRAFT 93/308130 DC REFERS TO AMENDMENT
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 161-1:1996 | Similar to |
| ISO 4435:2003 | Similar to |
| ISO 8283-1:1991 | Similar to |
| BS CP312-1(1973) : 1973 | CODE OF PRACTICE FOR PLASTICS PIPEWORK (THERMOPLASTICS MATERIAL) - GENERAL PRINCIPLES AND CHOICE OF MATERIAL |
| BS 4778-1:1987 | Quality vocabulary International terms |
| BS 2782-3 Method 365B:1981 | Methods of testing plastics. Mechanical properties Determination of indentation hardness by means of a durometer (Shore hardness) |
| BS 5955-6:1980 | Plastics pipework (thermoplastics materials) Code of practice for the installation of unplasticized PVC pipework for gravity drains and sewers |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
| BS 4778-2:1979 | Quality vocabulary National terms |
| BS 2782-11:Method 1101A:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Measurement of dimensions of pipes |
| BS 903-A26:1969 | Physical testing of rubber Determination of hardness |
| BS 2782-11:Method 1108A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves True impact rate (TIR) boundaries of pipes |
| BS 2782-11 Method 1102A:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: immersion bath method |
| BS 2782-11:Method 1109A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Resistance to environmental stress cracking of polyethylene pipes and fittings for non-pressure applications |
| BS 5834-2:1983 | Surface boxes, guards and underground chambers for gas and waterworks purposes Specification for small surface boxes |
| BS 2782-11 Method 1103A:1982 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Stress relief test for injection moulded fittings: oven method |
| BS 2782-1 Methods 120A to 120E:1976 | Methods of testing plastics. Thermal properties Determination of the Vicat softening temperature of thermoplastics |
| BS 4781-1:1973 | Specification for self-adhesive plastics labels for permanent use General purpose labels |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| BS 2782-11:Method 1110:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Tensile properties of dumb-bell specimens from PVC gutter profiles of pipes for non-pressure applications |
| BS 2782-11:Method 1112A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Leaktightness of thermoplastics pipes and fittings for non-pressure applications |
| BS 2782-11 Method 1102B:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: oven method |
| BS 1755-1:1982 | Glossary of terms used in the plastics industry Polymer and plastics technology |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.