BS 1722-12:2016
Current
The latest, up-to-date edition.
Fences Steel palisade fences. Manufacturing and installation. Specification
Hardcopy , PDF
English
09-30-2016
Foreword
1 Scope
2 Normative references
Section 1 - Manufacturers
3 Dimensions and general characteristics
4 Materials
5 Construction of the fence
6 Security purpose (SP) fences
7 Renovation and repair of hot dipped galvanized coatings
8 Construction of gates
Section 2 - Installers
9 Installation
10 Statement of conformity
Annexes
Annex A (normative) - Method for the determination
of characteristic flexural strength of pales
Annex B (normative) - Method for the determination
of characteristic flexural strength of posts
Annex C (normative) - Method for the determination
of characteristic flexural strength of rails
Annex D (normative) - Method of determination of
tensile strength of cold swaged pin and collar fixings
Annex E (normative) - Method of determination of
the strength of the pale to fence rail fastening assembly
Annex F (informative) - Specifying a steel palisade fence
Bibliography
Describes requirements for steel palisade fences and gates for general purpose (GP) fences for heights up to 2.4 m, and for security purpose (SP) fences for heights of 3 m and 3.6 m, all with posts at 2.75 m centres.
Committee |
B/201
|
DevelopmentNote |
Supersedes 16/30325063 DC and BS 1722-12(2006). (09/2016)
|
DocumentType |
Standard
|
ISBN |
9780580904981
|
Pages |
44
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
This part of BS1722 specifies requirements for steel palisade fences and gates for general purpose (GP) fences for heights up to 2.4m, and for security purpose (SP) fences for heights of 3m and 3.6m, all with posts at 2.75m centres. This British Standard also covers fences between 2.4m and 3m in height with components constructed to the SP specification. NOTE1 Where greater resistance against penetration is required for fences below 2.4m in height, the SP components should be obtained from the purchaser. NOTE2 Requirements in this British Standard for the minimum sizes of fence components are based on a design wind loading, q, at right angles to the plane of the fence of 900N/m 2 employing a shape factor of 1.9 on the net area presented to the wind. NOTE3 In situations of extreme exposure or abnormal loading, a special appraisal should be undertaken and the design criteria should be obtained from the purchaser. NOTE4 The responsibility for ensuring the final installation meets this British Standard belongs to the installer. This responsibility can be mitigated by obtaining certificates for materials used from the suppliers (see Clause 10 ).
BS EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
BS EN 287-1:2011 | Qualification test of welders. Fusion welding Steels |
BS EN 10056-1:2017 | Structural steel equal and unequal leg angles Dimensions |
BS EN 10263-3:2001 | Steel rod, bars and wire for cold heading and cold extrusion Technical delivery conditions for case hardening steels |
BS EN 10296-1:2003 | Welded circular steel tubes for mechanical and general engineering purposes. Technical delivery conditions Non-alloy and alloy steel tubes |
BS EN 10025-2:2004 | Hot rolled products of structural steels Technical delivery conditions for non-alloy structural steels |
BS EN 10263-1:2001 | Steel rod, bars and wire for cold heading and cold extrusion General technical delivery conditions |
BS EN 206 : 2013 | CONCRETE - SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY |
BS EN 10263-4:2001 | Steel rod, bars and wire for cold heading and cold extrusion Technical delivery conditions for steels for quenching and tempering |
BS EN 12620:2013 | Aggregates for concrete |
BS 4484-1:1969 | Specification for measuring instruments for constructional works Metric graduation and figuring of instruments for linear measurement |
BS EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
BS 7371-6(1998) : 1998 | COATINGS ON METAL FASTENERS - PART 6: SPECIFICATION FOR HOT DIPPED GALVANIZED COATINGS |
BS EN 10058:2003 | Hot rolled flat steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
BS EN ISO 376:2011 | Metallic materials. Calibration of force-proving instruments used for the verification of uniaxial testing machines |
BS EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods |
BS EN ISO 463:2006 | Geometrical Product Specifications (GPS). Dimensional measuring equipment. Design and metrological characteristics of mechanical dial gauges |
BS EN 1011-2:2001 | Welding. Recommendations for welding of metallic materials Arc welding of ferritic steels |
BS 3692:2014 | ISO metric precision hexagon bolts, screws and nuts. Specification |
BS EN 10219-2:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels Tolerances, dimensions and sectional properties |
BS EN 10210-2:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels Tolerances, dimensions and sectional properties |
BS 7805-1:1995 | Swaged collar grooved rivets Specification for sizes up to and including 10 mm diameter |
BS EN ISO 7500-1:2015 | Metallic materials. Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines. Calibration and verification of the force-measuring system |
BS 907:2008 | Specification for dial gauges for linear measurement |
BS EN 10263-2:2001 | Steel rod, bars and wire for cold heading and cold extrusion Technical delivery conditions for steels not intended for heat treatment after cold working |
BS 4320:1968 | Specification for metal washers for general engineering purposes. Metric series |
BS EN 1011-1:2009 | Welding. Recommendations for welding of metallic materials General guidance for arc welding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.