BS 1322:1992
Current
The latest, up-to-date edition.
Specification for aminoplastic moulding materials
Hardcopy , PDF
English
10-15-1992
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Committees responsible
National foreword
Specification
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 Test specimens
6 Methods of test
7 Marking
Table
1 Properties of aminoplastic moulding materials
Sets down a specification applicable to four types of aminoplastic moulding materials; takes in general purpose, hot-water resistant, heat resistant and electrical, and impact resistant. Coverage includes definitions, test specimens, marking and methods of test.
| Committee |
PRI/42
|
| DevelopmentNote |
Supersedes 87/38630 DC and BS 1322(1981). Also numbered as ISO 2112. (06/2005)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
1.1 This International Standard establishes a specification applicable to four types of aminoplastic moulding materials, classified according to use, as follows: Type UF A – General purpose Example: Urea-formaldehyde resin with cellulose filler. Type MF B – Hot-water resistant Example: Melamine-formaldehyde resin with cellulose filler. Type MF C – Heat resistant and electrical Example: Melamine-formaldehyde resin with inorganic filler. Type MF D – Impact resistant Example: Melamine-formaldehyde resin with chopped cotton-cloth filler. 1.2 These types have been further sub-divided into grades based on property levels and requirements, as follows:
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| BS 2782-3 Method 359:1984 | Methods of testing plastics. Mechanical properties Determination of Charpy impact strength of rigid materials (Charpy impact flexural test) |
| BS 2782-1 Method 121A and 121B:1991 | Methods of testing plastics. Thermal properties Determination of temperature of deflection of plastics under a bending stress |
| BS 2782-9.920A.C(1977) : 1977 | METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PREPARATION OF GLASS FIBRE REINFORCED, RESIN BONDED, LOW-PRESSURE LAMINATED PLATES OR PANELS FOR TEST PURPOSES |
| IEC 60243:1967 | Recommended methods of test for electric strength of solid insulating materials at power frequencies |
| BS 2782-4.461A(1978) : 1978 AMD 10345 | METHODS OF TESTING PLASTICS - CHEMICAL PROPERTIES - DETERMINATION OF VOLATILE MATTER IN AMINOPLASTIC MOULDING MATERIALS |
| BS 2782-3 Method 350:1984 | Methods of testing plastics. Mechanical properties Determination of Izod impact strength of rigid materials |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| BS 2782-6:Method 621C:1983 | Methods of testing plastics. Dimensional properties Determination of the bulk factor of moulding materials |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| BS 2782-3 Method 335A:1978 | Methods of testing plastics. Mechanical properties Determination of flexural properties of rigid plastics |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| BS 2782-4 Method 434A:1975 | Methods of testing plastics. Chemical properties The identification of antioxidants and ultra-violet absorbers in polyolefin compounds by thin layer chromatography |
| ISO 181:1981 | Plastics — Determination of flammability characteristics of rigid plastics in the form of small specimens in contact with an incandescent rod |
| BS 2782-4.430A.D(1983) : 1983 | METHODS OF TESTING PLASTICS - CHEMICAL PROPERTIES - DETERMINATION OF WATER AND BOILING WATER ABSORPTION AT 23 DEGREES C. DETERMINATION OF WATER AND BOILING WATER WITH ALLOWANCE OF WATER-SOLUBLE MATTER |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.