AWWA C906:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS
Hardcopy , PDF
12-13-2021
English
09-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Marking and Shipping
Appendixes
A - Internal Surge Pressure and Corresponding Sudden
Water Flow Velocity Change
B - Bibliography of Sources for Additional
Information Regarding Permeation of Polyolefin Pipes
Specifies polyethylene (PE) pressure pipe and fittings made from materials conforming to standard PE materials designation codes PE 2606, PE 2706, PE 2708, PE 3608, PE 3708, PE 3710, PE 4608, PE 4708, and PE 4710.
| DocumentType |
Revision
|
| ISBN |
9781625760999
|
| Pages |
52
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| AWWA M55 : 1 | PE PIPE - DESIGN AND INSTALLATION |
| ASTM F 2880 : 2014 : REDLINE | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in. |
| ASTM F 2620 : 2014-01 | PRACTICE FOR HEAT FUSION JOINING OF POLYETHYLENE PIPE AND FITTINGS |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| CSA Z245.20 SERIES : 2014 | PLANT-APPLIED EXTERNAL COATINGS FOR STEEL PIPE |
| FM 1613 : 2017 | POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| AWWA M28 : 2014 | REHABILITATION OF WATER MAINS |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| ASTM D 3261 : 2016-11 | SPECIFICATION FOR BUTT HEAT FUSION POLYETHYLENE (PE) PLASTIC FITTINGS FOR POLYETHYLENE (PE) PLASTIC PIPE AND TUBING |
| ASTM F 2620 : 2014-01 | PRACTICE FOR HEAT FUSION JOINING OF POLYETHYLENE PIPE AND FITTINGS |
| ASTM D 2839 : 2016 : REDLINE | Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| CAN/CSA-Z662-15 | Oil and gas pipeline systems |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| AWWA C150/A21.50 : 2014 | THICKNESS DESIGN OF DUCTILE-IRON PIPE |
| PPI TR 4 : 2017 | HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| CSA B137.1 : 2009 GEN INS 1 11 | POLYETHYLENE (PE) PIPE, TUBING, AND FITTINGS FOR COLD-WATER PRESSURE SERVICES |
| ASTM D 2683 : 2014 : REDLINE | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM D 1603 : 2014 : REDLINE | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM F 714 : 2013 : REDLINE | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| AWWA C901 : 2017 | POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE |
| ASTM F 2619/F2619M : 2013 : REDLINE | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| AWWA M55 : 1 | PE PIPE - DESIGN AND INSTALLATION |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1055 : 2016-09 | SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING |
| ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| CSA B137.4 : 2009 GEN INS 1 11 | POLYETHYLENE (PE) PIPING SYSTEMS FOR GAS SERVICES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.