AWWA C900 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 4 IN. THROUGH 60 IN. (100 MM THROUGH 1,500 MM)
Hardcopy , PDF
05-20-2023
English
08-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Marking and Delivery
Appendixes
A - Bibliography
B - Recurring (Cyclic) Surge
Includes polyvinyl chloride (PVC) pipe and fabricated fittings manufactured for conveying potable water, reclaimed water, irrigation water, wastewater, or any fluid compatible with nonplasticized PVC.
| DevelopmentNote |
Supersedes AWWA C905. (07/2016)
|
| DocumentType |
Revision
|
| ISBN |
9781625761750
|
| Pages |
52
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASCE/EWRI 12-13, 13-13, 14-13 : 2013 | STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE |
| ASTM F 2946 : 2012 : R2017 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASHRAE GHCDGS HEAT PUMP SYSTEMS : 2014 ERRATA 2016 | GEOTHERMAL HEATING AND COOLING DESIGN OF GROUND-SOURCE HEAT PUMP SYSTEMS |
| AWWA C908 : 2001 | PVC SELF-TAPPING SADDLE TEES FOR USE ON PVC PIPE |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| ASME B31.3:2016 | PROCESS PIPING |
| AWWA C905 : 2010 | POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 14 IN. THROUGH 48 IN. (350 MM THROUGH 1,200 MM), FOR WATER TRANSMISSION AND DISTRIBUTION |
| ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 | IRC® Code and Commentary, Volume 2 |
| AWWA C605 : 2013 | UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS |
| AWWA C907 : 2017 | INJECTION-MOLDED POLYVINYL CHLORIDE (PVC) PRESSURE FITTINGS, 4 IN. THROUGH 12 IN. (100 MM THROUGH 300 MM), FOR WATER, WASTEWATER, AND RECLAIMED WATER SERVICE |
| FM 1612 : 2016 | POLYVINYL CHLORIDE (PVC) PIPE AND FITTING FOR UNDERGROUND FIRE PROTECTION SERVICE |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| AWWA M28 : 2014 | REHABILITATION OF WATER MAINS |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| ASTM F 2946 :2012 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| ASME B36.10 : 1979 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM F 477 : 2014 : REDLINE | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 2855 : 2015 : REDLINE | Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets |
| AWWA C907 : 2017 | INJECTION-MOLDED POLYVINYL CHLORIDE (PVC) PRESSURE FITTINGS, 4 IN. THROUGH 12 IN. (100 MM THROUGH 300 MM), FOR WATER, WASTEWATER, AND RECLAIMED WATER SERVICE |
| AWWA C110/A21.10 : 2012 | DUCTILE-IRON AND GRAY-IRON FITTINGS |
| AWWA C605 : 2013 | UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1784 : 2011 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.