AWWA C303 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CONCRETE PRESSURE PIPE, BAR-WRAPPED, STEEL-CYLINDER TYPE
Hardcopy , PDF
08-09-2024
English
04-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Specifies the manufacture of concrete pressure pipe, reinforced with a steel cylinder that is helically wrapped with mild steel bar reinforcement, in sizes ranging from 10 in. through 72 in. (250 mm through 1,830 mm), inclusive, and for working pressures up to 400 psi (2,760 kPa).
| DocumentType |
Revision
|
| ISBN |
9781625762122
|
| Pages |
44
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ACI 224.3R : 1995 | JOINTS IN CONCRETE CONSTRUCTION |
| AWWA M27 : 3 | EXTERNAL CORROSION CONTROL FOR INFRASTRUCTURE SUSTAINABILITY |
| NACE SP 01 00 : 2014 | CATHODIC PROTECTION TO CONTROL EXTERNAL CORROSION OF CONCRETE PRESSURE PIPELINES AND MORTAR-COATED STEEL PIPELINES FOR WATER OR WASTE WATER SERVICE |
| ASCE/EWRI 12-13, 13-13, 14-13 : 2013 | STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| AWWA M9 : 2008 | CONCRETE PRESSURE PIPE |
| ASTM D 297 : 2015 : REDLINE | Standard Test Methods for Rubber Products—Chemical Analysis |
| AWS D1.3/D1.3M : 2008 | STRUCTURAL WELDING CODE-SHEET STEEL |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| ASTM E 340 : 2015 : REDLINE | Standard Practice for Macroetching Metals and Alloys |
| AWS D1.4/D1.4M : 2011 | STRUCTURAL WELDING CODE - REINFORCING STEEL |
| ASTM C 309 : 2011 : REDLINE | Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete |
| AWS A3.0 : 0 | STANDARD WELDING TERMS AND DEFINITIONS - INCLUDING TERMS FOR ADHESIVE BONDING, BRAZING, SOLDERING, THERMAL CUTTING, AND THERMAL SPRAYING |
| AWS QC1 : 2007 | STANDARD FOR AWS CERTIFICATION OF WELDING INSPECTORS |
| AWWA M9 : 2008 | CONCRETE PRESSURE PIPE |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| AWWA C210 : 2015 | LIQUID-EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.