ASTM F 879 : 2015 : R2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws
Hardcopy , PDF
11-23-2023
English
04-14-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 16
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the chemical and mechanical requirements for stainless steel inch hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread 0.060 through 0.625 in. intended for use in applications requiring general corrosion resistance.
1.2Two groups of austenitic stainless steel alloys and three conditions are covered. See Table 1 and Table 2.
1.3Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1921/C1921M : 2022 | Standard Test Method for Comparative Impact Testing of Gypsum Panel Outside 90° Corner Systems |
| ASTM A 555/A555M : 2020 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM F 606/F606M : 2019 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM E 384 : 2022 | Standard Test Method for Microindentation Hardness of Materials |
| ASTM A 555/A555M : 2021 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 342/A342M : 2014 | Standard Test Methods for Permeability of Weakly Magnetic Materials |
| ASTM A 262 : 2001 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 384 : 2011 | Standard Test Method for Knoop and Vickers Hardness of Materials |
| ASTM F 593 : 2022 | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| ASTM E 92 : 2017 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM A 555/A555M : 2022 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 262 : 1998 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM F 593 : 2017 | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| ASTM A 262 : 2015 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM E 18 : 2019 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 92 : 1982 : R2003 : EDT 2 | Standard Test Method for Vickers Hardness of Metallic Materials (Withdrawn 2010) |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM E 384 : 2017 | Standard Test Method for Microindentation Hardness of Materials |
| ASTM A 342/A342M : 2021 | Standard Test Methods for Permeability of Weakly Magnetic Materials |
| ASTM F 606/F606M : 2021 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM A 262 : 2015 : R2021 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.