ASTM F 3273 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Wrought Molybdenum-47.5 Rhenium Alloy for Surgical Implants (UNS R03700)
Hardcopy , PDF
01-06-2022
English
09-18-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers the chemical, mechanical, and metallurgical requirements for wrought molybdenum-47.5 rhenium alloy to be used in the manufacture of surgical implants.
| Committee |
F 04
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers the chemical, mechanical, and metallurgical requirements for wrought molybdenum-47.5 rhenium alloy to be used in the manufacture of surgical implants.
1.2The SI units in this standard are the primary units. The values stated in either primary SI units or secondary inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1941 : 2010 : R2016 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis |
| ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 1941 : 2010 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis |
| ASTM E 1621 : 2013 | Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
| SAE AMS 2630 : 2010 | INSPECTION, ULTRASONIC, PRODUCT OVER 0.5 INCH (12.7 MM) THICK |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| SAE AMS 2632 : 1995 | INSPECTION, ULTRASONIC, OF THIN MATERIALS 0.5 INCH (12.77 MM) AND UNDER IN CROSS-SECTIONAL THICKNESS |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 311 : 2017 : REDLINE | Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity |
| ASTM E 1621 : 2005 | Standard Guide for X-Ray Emission Spectrometric Analysis |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ASTM B 311 : 1993 : R1997 | Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM E 2626 : 2008 | Standard Guide for Spectrometric Analysis of Reactive and Refractory Metals |
| ASTM E 1621 : 2021 | Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
| ISO 10993-10:2010 | Biological evaluation of medical devices Part 10: Tests for irritation and skin sensitization |
| ISO 10993-11:2017 | Biological evaluation of medical devices — Part 11: Tests for systemic toxicity |
| ASTM E 1941 : 2004 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys |
| ASTM E 1621 : 2013 : REDLINE | Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
| ISO 9001:2015 | Quality management systems — Requirements |
| ASTM E 2626 : 2008 : EDT 1 | Standard Guide for Spectrometric Analysis of Reactive and Refractory Metals (Withdrawn 2017) |
| ASTM E 290 : 2014 : REDLINE | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM B 193 : 2016 : REDLINE | Standard Test Method for Resistivity of Electrical Conductor Materials |
| ASTM E 1621 : 1994 : R1999 | Standard Guide for X-Ray Emission Spectrometric Analysis |
| ASTM E 1941 : 1998 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys |
| ASTM B 774 : 2000 : R2014 | Standard Specification for Low Melting Point Alloys |
| ISO 10993-6:2016 | Biological evaluation of medical devices Part 6: Tests for local effects after implantation |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
| ASTM C 1113 : 1999 | Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.