ASTM F 3165 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Throat Protective Equipment for Hockey Goaltenders
Hardcopy , PDF
07-01-2022
English
03-17-2016
CONTAINED IN VOL. 15.07, 2016 Defines performance requirements and test methods for throat protectors marketed, sold, and intended for ice hockey goalkeepers.
Committee |
F 08
|
DocumentType |
Standard
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers performance requirements and test methods for throat protectors marketed, sold, and intended for ice hockey goalkeepers.
1.2The intent of this specification is to reduce the risk of injury to the throat without compromising the form or appeal of the game. To do so, the protector shall be used:
1.2.1As intended within the rules of the game and
1.2.2In accordance with the manufacturer’s instructions.
1.3Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a throat protector certified to this specification will not prevent all injuries.
1.4This specification has been prepared after careful consideration of the frequency and mechanisms associated with throat injuries that can potentially occur within the rules of the game of ice hockey.
1.5Requirements and the corresponding test methods, where appropriate, are given for the following:
1.5.1Construction,
1.5.2Puck impact resistance,
1.5.3Coverage,
1.5.4Marking and information.
1.6Throat protection is intended for use by goalkeepers.
1.7Use of the singular does not exclude the plural (and vice versa) when the sense allows.
1.8Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.
1.9The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.10This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.