ASTM F 2600 : 2009 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
Hardcopy , PDF
11-13-2023
English
03-28-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.04, 2018 Defines polyamide-11 electrofusion fittings for use with outside diameter-controlled polyamide-11 pipe, covered by Specification D 2513.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
10
|
| ProductNote |
Reconfirmed 2018
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers polyamide-11 electrofusion fittings for use with outside diameter-controlled polyamide-11 pipe, covered by Specification D2513. Requirements for materials, workmanship, and testing performance are included. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.”
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2945 : 2018 | Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 6779 : 2002 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2005 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2020 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 905 : 2004 : R2018 | Standard Practice for Qualification of Polyethylene Saddle-Fused Joints |
| ASTM D 6779 : 2007 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 6779 : 2003 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2011 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 1598 : 2023 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 6779 : 2008 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2004 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 6779 : 2012 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 6779 : 2006 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 6779 : 2004 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2023 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2122 : 2022 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 6779 : 2012 : REV A | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 1598 : 2021 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 6779 : 2002 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 905 : 2004 : R2022 | Standard Practice for Qualification of Polyethylene Saddle-Fused Joints |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 6779 : 2016 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2007 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2021 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2010 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 6779 : 2017 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2008 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 6779 : 2006 : EDT 1 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.